Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Ten blue 2.85mm filament spools in a pack

Taulman 3D

Taulman 3D t-glase 3D Printers Accessory 2.85mm Blue 10 pack

SKU CH-Q14A-2135Y

Pack of ten 2.85 mm blue PET co-polymer spools made for direct food contact with very low shrinkage and glass-like clarity

  • ColorBlue
  • TypeFilament
  • Food-safe polymer approved for direct contact
  • Very low shrinkage eases large flat prints
  • Stronger than ABS for durable parts
  • Glass-like clarity with optical coatings
  • 10 spools of 2.85 mm blue filament

2.85 mm PET co-polymer filament pack

This ten-spool pack supplies 2.85 mm t-glase filament for desktop 3D printers. The material is a PET co-polymer formulated for direct food contact and offers higher strength than ABS. It is intended for intermediate users who need transparent, durable parts.

Low-shrink behaviour on extended prints

Very low shrinkage keeps large flat surfaces dimensionally stable during long print sessions. The filament prints at 235-245 °C and adheres to acrylic, glass or Kapton without a heated bed. Slower print speeds are required compared with standard filaments.

Printer compatibility checklist

Confirm your printer accepts 2.85 mm filament and can reach 235-245 °C nozzle temperature. A heated bed is not mandatory but the platform must be acrylic, glass, Kapton or similar. Allow extra print time because t-glase runs slower than beginner materials.

Helstu kostir

  • Food-safe polymer approved for direct contact
  • Very low shrinkage eases large flat prints
  • Stronger than ABS for durable parts
  • Glass-like clarity with optical coatings
  • 10 spools of 2.85 mm blue filament

Tæknilýsing

ColorBlue
TypeFilament

Spurningar um þessa vöru

How much heat does the t-glase filament need from the hot-end during long prints?

The filament prints at 235-245 °C, so the hot-end must sustain that temperature continuously during extended sessions.

What printer parts are required to use the 2.85 mm spools?

A printer with a 2.85 mm extruder and a nozzle that accepts 2.85 mm filament is needed; the material also works on acrylic, glass, Kapton or other flat platforms even without a heated bed.

Will the blue t-glase bond well to older PLA or ABS prints I want to extend?

t-glase is a PET co-polymer with different thermal behaviour, so layer adhesion to existing PLA or ABS parts is limited; mechanical fastening or fresh dual-material printing is recommended.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.