저희는 암호화폐로 결제를 받습니다 — 보유하신 코인으로 실제 하드웨어를 구매하실 수 있습니다.암호화폐로 결제하고, 실제 하드웨어 구매에 사용하십시오. 전 세계 어디서나 US$399 이상 구매 시 무료 보험 배송. 무지 상자에 담아 독일에서 발송합니다.US$399 이상 구매 시 무료 보험 배송. 체크아웃을 시작하면 30분 동안 환율이 잠깁니다.30분간 환율 잠금. 모든 제품은 밀봉된 상태로 일련번호를 확인한 후 24개월 보증을 제공합니다.밀봉 포장, 24개월 보증.

가격 추적 로그인
Ten blue 2.85mm filament spools in a pack

Taulman 3D

Taulman 3D t-glase 3D Printers Accessory 2.85mm Blue 10 pack

SKU CH-Q14A-2135Y

Pack of ten 2.85 mm blue PET co-polymer spools made for direct food contact with very low shrinkage and glass-like clarity

  • ColorBlue
  • TypeFilament
  • Food-safe polymer approved for direct contact
  • Very low shrinkage eases large flat prints
  • Stronger than ABS for durable parts
  • Glass-like clarity with optical coatings
  • 10 spools of 2.85 mm blue filament

2.85 mm PET co-polymer filament pack

This ten-spool pack supplies 2.85 mm t-glase filament for desktop 3D printers. The material is a PET co-polymer formulated for direct food contact and offers higher strength than ABS. It is intended for intermediate users who need transparent, durable parts.

Low-shrink behaviour on extended prints

Very low shrinkage keeps large flat surfaces dimensionally stable during long print sessions. The filament prints at 235-245 °C and adheres to acrylic, glass or Kapton without a heated bed. Slower print speeds are required compared with standard filaments.

Printer compatibility checklist

Confirm your printer accepts 2.85 mm filament and can reach 235-245 °C nozzle temperature. A heated bed is not mandatory but the platform must be acrylic, glass, Kapton or similar. Allow extra print time because t-glase runs slower than beginner materials.

주요 특징

  • Food-safe polymer approved for direct contact
  • Very low shrinkage eases large flat prints
  • Stronger than ABS for durable parts
  • Glass-like clarity with optical coatings
  • 10 spools of 2.85 mm blue filament

사양

ColorBlue
TypeFilament

이 상품에 대한 질문

How much heat does the t-glase filament need from the hot-end during long prints?

The filament prints at 235-245 °C, so the hot-end must sustain that temperature continuously during extended sessions.

What printer parts are required to use the 2.85 mm spools?

A printer with a 2.85 mm extruder and a nozzle that accepts 2.85 mm filament is needed; the material also works on acrylic, glass, Kapton or other flat platforms even without a heated bed.

Will the blue t-glase bond well to older PLA or ABS prints I want to extend?

t-glase is a PET co-polymer with different thermal behaviour, so layer adhesion to existing PLA or ABS parts is limited; mechanical fastening or fresh dual-material printing is recommended.

이 진열대의 다른 상품

고객들이 함께 비교한 상품

같은 진열대, 같은 체크아웃 — 코인 8종, 환율 잠금 30분.