Priimame kriptovaliutą — taip monetos, kurias turite, gali nupirkti tikrą techniką.Mokėkite kriptovaliuta, išleiskite ją tikrai technikai. Nemokamas apdraustas pristatymas visame pasaulyje virš 399 $. Paprastos, be žymų siuntos dėžės, siunčiamos iš Vokietijos.Nemokamas apdraustas pristatymas virš 399 $. Jūsų kursas fiksuojamas 30 minučių, kai tik prasideda atsiskaitymas.Kursas fiksuojamas 30 minučių. Kiekvienas gaminys užplombuotas, jo serijos numeris patikrintas, ir jam taikoma 24 mėnesių garantija.Užplombuota, 24 mėnesių garantija.

Stebimos prekės Prisijungti
Ten blue 2.85mm filament spools in a pack

Taulman 3D

Taulman 3D t-glase 3D Printers Accessory 2.85mm Blue 10 pack

SKU CH-Q14A-2135Y

Pack of ten 2.85 mm blue PET co-polymer spools made for direct food contact with very low shrinkage and glass-like clarity

  • ColorBlue
  • TypeFilament
  • Food-safe polymer approved for direct contact
  • Very low shrinkage eases large flat prints
  • Stronger than ABS for durable parts
  • Glass-like clarity with optical coatings
  • 10 spools of 2.85 mm blue filament

2.85 mm PET co-polymer filament pack

This ten-spool pack supplies 2.85 mm t-glase filament for desktop 3D printers. The material is a PET co-polymer formulated for direct food contact and offers higher strength than ABS. It is intended for intermediate users who need transparent, durable parts.

Low-shrink behaviour on extended prints

Very low shrinkage keeps large flat surfaces dimensionally stable during long print sessions. The filament prints at 235-245 °C and adheres to acrylic, glass or Kapton without a heated bed. Slower print speeds are required compared with standard filaments.

Printer compatibility checklist

Confirm your printer accepts 2.85 mm filament and can reach 235-245 °C nozzle temperature. A heated bed is not mandatory but the platform must be acrylic, glass, Kapton or similar. Allow extra print time because t-glase runs slower than beginner materials.

Privalumai

  • Food-safe polymer approved for direct contact
  • Very low shrinkage eases large flat prints
  • Stronger than ABS for durable parts
  • Glass-like clarity with optical coatings
  • 10 spools of 2.85 mm blue filament

Specifikacijos

ColorBlue
TypeFilament

Klausimai apie šią prekę

How much heat does the t-glase filament need from the hot-end during long prints?

The filament prints at 235-245 °C, so the hot-end must sustain that temperature continuously during extended sessions.

What printer parts are required to use the 2.85 mm spools?

A printer with a 2.85 mm extruder and a nozzle that accepts 2.85 mm filament is needed; the material also works on acrylic, glass, Kapton or other flat platforms even without a heated bed.

Will the blue t-glase bond well to older PLA or ABS prints I want to extend?

t-glase is a PET co-polymer with different thermal behaviour, so layer adhesion to existing PLA or ABS parts is limited; mechanical fastening or fresh dual-material printing is recommended.

Taip pat šiame skyriuje

Kiti pirkėjai taip pat lygino

Ta pati lentyna, tas pats atsiskaitymas — aštuonios monetos ir 30 minučių fiksuotas kursas.