Við tökum við rafmynt — svo myntirnar sem þú átt geta keypt alvöru vélbúnað.Greiddu í rafmynt, eyddu henni í alvöru vélbúnað. Frí, tryggð sending um allan heim fyrir pantanir yfir 399 $. Hlutlausir pappakassar án merkinga, sendir frá Þýskalandi.Frí, tryggð sending yfir 399 $. Gengið þitt er læst í 30 mínútur um leið og greiðsluferlið hefst.Gengið læst í 30 mínútur. Hver vara er innsigluð, raðnúmer hennar yfirfarið, og hún nýtur 24 mánaða ábyrgðar.Innsiglað, með 24 mánaða ábyrgð.

Vaktaðar vörur Skrá inn
Black 80mm square case fan 38mm thick four-wire ball bearing 12V 3.6A

Zyvpee

Zyvpee DBPD0838B2U 80x38mm 12V 3.6A 4-wire ball bearing case fan

SKU CH-6GF0-48A6B

An 80 mm by 38 mm dual-ball-bearing case fan spinning above 7000 RPM and pushing over 80 CFM from a 12 V four-wire connection

  • TypeCase Fan
  • CompatibilityCase
  • Bearing Type2 Ball
  • RPM>7000 RPM
  • Air Flow>80 CFM
  • Power Connector4 Wires
  • High airflow over 80 CFM for strong cooling
  • Dual ball bearing rated for long service life
  • 7000 RPM maximum speed delivers high static pressure
  • 4-wire PWM connector enables precise speed control
  • Compact 80 by 38 mm frame fits tight chassis

80 mm 4-wire ball-bearing case fan

The Zyvpee DBPD0838B2U is an 80 mm axial fan built for case ventilation. It runs on 12 V DC and draws 3.6 A through a standard 4-wire PWM connector. The double ball bearing is rated for continuous operation in server or workstation chassis. Black frame and blades with no LED lighting keep the appearance neutral.

Sustained airflow above 80 CFM at over 7000 RPM

At full speed the fan moves more than 80 CFM while spinning above 7000 RPM. The 38 mm thick frame houses a motor designed to maintain that output without throttling during extended loads. The 4-wire interface allows the motherboard to modulate speed in response to temperature curves. Performance stays consistent in restricted airflow paths typical of dense drive bays or GPU cages.

Ball bearing runs quietly at moderate PWM duty

Under typical PWM curves the double ball bearing produces a smooth broadband sound without the rattle of sleeve units. Power draw scales with RPM, so idle speeds keep consumption well below the 3.6 A maximum. The 12 V supply rail sees minimal ripple because the fan controller is integrated. No LED circuitry means one less heat source inside the housing.

Helstu kostir

  • High airflow over 80 CFM for strong cooling
  • Dual ball bearing rated for long service life
  • 7000 RPM maximum speed delivers high static pressure
  • 4-wire PWM connector enables precise speed control
  • Compact 80 by 38 mm frame fits tight chassis

Tæknilýsing

SeriesDBPD0838B2U
ModelDBPD0838B2U
TypeCase Fan
CompatibilityCase
Bearing Type2 Ball
RPM>7000 RPM
Air Flow>80 CFM
Power Connector4 Wires
ColorBlack
LEDNon-LED
FeaturesDC square Cooler
Dimensions80*80*38mm

Spurningar um þessa vöru

How loud and hot does the 80x38mm fan get when it runs above 7000 RPM continuously?

At over 7000 RPM the 12 V motor draws 3.6 A, so expect noticeable airflow noise and measurable heat output during all-day operation.

What must my case or controller provide to run the 4-wire 12 V 3.6 A connector?

A standard 4-pin PWM header rated for at least 12 V and 3.6 A is required; the fan will not start on a 3-pin or lower-current header.

Will the 80x38mm frame and >80 CFM output fit and cool a legacy 80 mm mount without adapter brackets?

Yes, the 80x80x38 mm dimensions match the classic 80 mm mounting pattern, and the high airflow works with older heatsinks designed for that spacing.

Einnig í þessum vöruflokki

Fólk bar þetta saman

Sama hilla, sama greiðsluferli — átta myntir og 30 mínútna gengislæsing.