Mēs pieņemam kriptovalūtu — lai tā, kas Jums pieder, varētu nopirkt īstu aparatūru.Maksājiet kriptovalūtā, iztērējiet to īstai aparatūrai. Bezmaksas apdrošināta piegāde visā pasaulē virs 399 $. Vienkāršas, nemarķētas kastes, sūtītas no Vācijas.Bezmaksas apdrošināta piegāde virs 399 $. Jūsu kurss tiek fiksēts uz 30 minūtēm, tiklīdz atveras kase.Kurss fiksēts uz 30 minūtēm. Katra prece ir aizzīmogota, tās sērijas numurs ir pārbaudīts, un uz to attiecas 24 mēnešu garantija.Aizzīmogots, 24 mēnešu garantija.

Uzraudzītās preces Pieteikties
Seven inch touch display board with glass front and exposed circuit board

LORDWORLD

LORDWORLD 7 inch 1024×600 Capacitive Touch Display development board

SKU CH-PYK2-BGDRW

7-inch capacitive IPS touch display for Raspberry Pi with 1024×600 resolution and up to five touch points

  • 1024×600 IPS panel gives sharp visuals for Raspberry Pi projects
  • Up to five simultaneous touch points enable multi-finger interaction
  • Software-controlled brightness adjusts to any lighting condition
  • Works with Pi 4B, 3B+, 3A+ and Compute Modules 3+/4
  • DSI interface connects directly without extra wiring

7-inch Capacitive Touch Development Board

This LORDWORLD display board provides a 1024×600 IPS panel with a capacitive touch layer for Raspberry Pi projects. It connects through the DSI interface and supports Pi 4B, 3B+, 3A+, CM3+ and CM4 when an extra adapter board is used. Driver installation is required on Raspbian.

Sustained Operation Behaviour

Brightness is adjustable via software so the panel can be dimmed for long-running kiosk or dashboard use without generating excess heat. The five-point touch capability remains responsive during continuous interaction, limited only by the operating system's touch stack. No active cooling is integrated on the board itself.

DSI Interface and Adapter Requirement

The single deciding specification is the DSI connector combined with the mandatory adapter board for Compute Module 3+ and 4 variants. Builds that rely on HDMI or lack the adapter cannot use this display, while standard Pi 4B, 3B+ and 3A+ models connect directly.

Priekšrocības

  • 1024×600 IPS panel gives sharp visuals for Raspberry Pi projects
  • Up to five simultaneous touch points enable multi-finger interaction
  • Software-controlled brightness adjusts to any lighting condition
  • Works with Pi 4B, 3B+, 3A+ and Compute Modules 3+/4
  • DSI interface connects directly without extra wiring

Specifikācijas

BrandLORDWORLD

Jautājumi par šo preci

How much power does the 7 inch 1024×600 display draw when running all day on a Raspberry Pi?

The display connects through the Pi's DSI interface and draws power directly from the board; no separate supply is needed, so total consumption stays within the Pi's normal USB-C budget.

What extra hardware is required before the 7 inch 1024×600 touch screen will work?

You need a Raspberry Pi 4B, 3B+ or 3A+ with a DSI ribbon cable; for Compute Module 3+ or 4 an additional adapter board is also required.

Will the 7 inch 1024×600 display work with an original Raspberry Pi 1 or Pi 2 that I still own?

No — the board only supports Pi 4B, 3B+, 3A+ and Compute Module 3+/4, so older Pi 1 or Pi 2 models cannot drive the DSI interface.

Arī šajā sadaļā

Klienti arī salīdzināja

Tas pats plaukts, tā pati kase — astoņas kriptovalūtas un kursa fiksēšana uz 30 minūtēm.