Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Seven inch touch display board with glass front and exposed circuit board

LORDWORLD

LORDWORLD 7 inch 1024×600 Capacitive Touch Display development board

SKU CH-PYK2-BGDRW

7-inch capacitive IPS touch display for Raspberry Pi with 1024×600 resolution and up to five touch points

  • 1024×600 IPS panel gives sharp visuals for Raspberry Pi projects
  • Up to five simultaneous touch points enable multi-finger interaction
  • Software-controlled brightness adjusts to any lighting condition
  • Works with Pi 4B, 3B+, 3A+ and Compute Modules 3+/4
  • DSI interface connects directly without extra wiring

7-inch Capacitive Touch Development Board

This LORDWORLD display board provides a 1024×600 IPS panel with a capacitive touch layer for Raspberry Pi projects. It connects through the DSI interface and supports Pi 4B, 3B+, 3A+, CM3+ and CM4 when an extra adapter board is used. Driver installation is required on Raspbian.

Sustained Operation Behaviour

Brightness is adjustable via software so the panel can be dimmed for long-running kiosk or dashboard use without generating excess heat. The five-point touch capability remains responsive during continuous interaction, limited only by the operating system's touch stack. No active cooling is integrated on the board itself.

DSI Interface and Adapter Requirement

The single deciding specification is the DSI connector combined with the mandatory adapter board for Compute Module 3+ and 4 variants. Builds that rely on HDMI or lack the adapter cannot use this display, while standard Pi 4B, 3B+ and 3A+ models connect directly.

Poudarki

  • 1024×600 IPS panel gives sharp visuals for Raspberry Pi projects
  • Up to five simultaneous touch points enable multi-finger interaction
  • Software-controlled brightness adjusts to any lighting condition
  • Works with Pi 4B, 3B+, 3A+ and Compute Modules 3+/4
  • DSI interface connects directly without extra wiring

Specifikacije

BrandLORDWORLD

Vprašanja o tem izdelku

How much power does the 7 inch 1024×600 display draw when running all day on a Raspberry Pi?

The display connects through the Pi's DSI interface and draws power directly from the board; no separate supply is needed, so total consumption stays within the Pi's normal USB-C budget.

What extra hardware is required before the 7 inch 1024×600 touch screen will work?

You need a Raspberry Pi 4B, 3B+ or 3A+ with a DSI ribbon cable; for Compute Module 3+ or 4 an additional adapter board is also required.

Will the 7 inch 1024×600 display work with an original Raspberry Pi 1 or Pi 2 that I still own?

No — the board only supports Pi 4B, 3B+, 3A+ and Compute Module 3+/4, so older Pi 1 or Pi 2 models cannot drive the DSI interface.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.