Kami menerima kripto — jadi koin yang anda simpan boleh membeli perkakasan sebenar.Bayar dengan kripto, belanjakannya untuk perkakasan sebenar. Penghantaran berinsurans percuma ke seluruh dunia untuk belian melebihi USD 399. Kotak biasa tanpa jenama, dihantar dari Jerman.Penghantaran berinsurans percuma untuk belian melebihi USD 399. Kadar anda dikunci selama 30 minit sebaik sahaja proses pesanan bermula.Kadar dikunci selama 30 minit. Setiap item disegel, nombor sirinya disemak, dan dilindungi waranti 24 bulan.Disegel, waranti 24 bulan.

Barang disimpan Log masuk
Four chrome 90-degree rotatable compression fittings with G1/4 threads for 16/10mm tubing

Alphacool

Alphacool Eiszapfen 16/10mm 90° Rotatable G1/4 Chrome 4-Pack (17614)

SKU CH-V0HD-NM52D

Pack of four chrome 90-degree rotatable G1/4 compression fittings for 16/10mm tubing

  • TypeFittings

Size 16/10mm

  • 90° rotatable design simplifies complex hose routing
  • G1/4 thread fits 95% of water-cooling components
  • Chrome coating bonded to resist chipping and peeling
  • 360° rotation on threaded side allows flexible alignment
  • High-flow 16/10 mm compression fitting for 3/8" ID hose

High-Flow Chrome Fittings

Alphacool Eiszapfen 16/10mm 90° rotatable compression fittings join 3/8" ID by 5/8" OD tubing to any G1/4 threaded port. The four-pack supplies enough chrome-plated brass connectors for a typical custom loop. Each fitting rotates 360° for stress-free routing and the 90° bend keeps tubing runs clean inside tight cases.

Loop Builders Wanting Clean Angles

These suit enthusiasts assembling hard-tube or soft-tube loops who need a right-angle turn without extra adapters. The rotatable base eliminates alignment guesswork during assembly. Builders who require straight-through or 45° profiles, or who prefer matte black accents, should look at other Eiszapfen variants.

G1/4 Thread With 90° Rotatable Bend

The single deciding spec is the combination of a standard G1/4 thread and a 90° rotatable elbow that accepts 16/10mm hose. If your block, radiator or reservoir uses G1/4 ports and your tubing matches 16/10mm, this four-pack completes the connection; otherwise a different thread or hose size is required.

Ciri-ciri utama

  • 90° rotatable design simplifies complex hose routing
  • G1/4 thread fits 95% of water-cooling components
  • Chrome coating bonded to resist chipping and peeling
  • 360° rotation on threaded side allows flexible alignment
  • High-flow 16/10 mm compression fitting for 3/8" ID hose

Spesifikasi

TypeFittings

Versi lain model ini

1 lagi dalam julat yang sama

Keluarga yang sama, memori, penyejuk atau kelajuan jam yang berbeza — bandingkan sebelum membuat keputusan.

Soalan tentang produk ini

Does the rotatable G1/4 thread on these 90° fittings need any extra power or cooling when the loop runs all day?

No — these are passive brass compression fittings with a 360° rotatable G1/4 thread, so they add no heat, noise or power draw to a continuous loop.

What hose size must I already have for the 16/10mm barb on each fitting to seal properly?

You need tubing with a 10 mm inner diameter and 16 mm outer diameter (3/8" ID × 5/8" OD) to match the 16/10mm compression end.

Will the 5 mm G1/4 thread length on these chrome fittings reach the ports on my older water blocks and radiators?

The 5 mm thread is the standard G1/4 length used on 95 % of components, so it fits most legacy blocks and radiators without spacers.

Juga di rak ini

Pelanggan turut membandingkan

Rak yang sama, checkout yang sama — lapan koin kripto dan kunci kadar 30 minit.