Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Brass 90-degree elbow fitting with dual female G 1/4 threads, 19.7mm square profile

PrimoChill

PrimoChill Female-Female G 1/4 90° SX Elbow Fitting 19.7mm diy cooling

SKU CH-HVS2-3XGH7

Connects two female G 1/4 threads at a 90° angle with 19.7 mm coated brass elbows for compact liquid-cooling loops

  • TypeCPU Block

Option UV Red

Vis 9 flere konfigurasjoner

Overstrøkne versjoner finnes, men er ikke på lager her.

  • 90° turn simplifies tight-loop routing
  • Dual female G1/4 threads accept standard fittings
  • Coated brass resists corrosion in liquid loops
  • 7 mm square profile fits confined spaces
  • Single-piece elbow removes extra connection points

G 1/4 90° Elbow for Custom Loops

The PrimoChill Female-Female G 1/4 90° SX Elbow Fitting connects two male-threaded components at a right angle inside a liquid-cooling loop. Its coated brass body resists corrosion while keeping the flow path short. The 19.7 mm square profile fits tight routing channels. It is sold individually for DIY cooling builds.

Suits Builders Needing a Compact Turn

This fitting suits builders who must change tube direction by 90 degrees without adding extra tubing length. It is not for loops that require a rotary joint for alignment after tightening. Buyers who need to join more than one RevolverSX fitting should choose a different connector because the manufacturer warns against that combination.

Simple Install with Standard Threads

Installation uses the two female G 1/4 threads; screw a male fitting into each side and tighten by hand plus a quarter turn. The fixed 90° angle means the outlet orientation cannot be adjusted once sealed, so dry-fit the loop first. Over-tightening can damage the coated brass threads, which is the most common issue reported.

Høydepunkter

  • 90° turn simplifies tight-loop routing
  • Dual female G1/4 threads accept standard fittings
  • Coated brass resists corrosion in liquid loops
  • 7 mm square profile fits confined spaces
  • Single-piece elbow removes extra connection points

Spesifikasjoner

TypeCPU Block

Andre versjoner av denne modellen

5 flere i samme serie

Samme familie, annet minne, annen kjøler eller klokkefrekvens — sammenlign før du bestemmer deg.

Spørsmål om denne varen

What thread size must my existing fittings have to connect to this elbow?

Both ends use female G 1/4 threads, so any male G 1/4 fitting will screw straight in.

Can I chain this 90° elbow directly to a RevolverSX fitting in the same loop?

The manufacturer warns against using more than one RevolverSX fitting with this elbow, so plan only a single RevolverSX connection.

How do I confirm the elbow is seated correctly after installation?

Check that each side measures 19.7 mm across the flats and that no coolant leaks appear when the loop is pressurised.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.