Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Brass 90-degree elbow fitting with dual female G 1/4 threads, 19.7mm square profile

PrimoChill

PrimoChill Female-Female G 1/4 90° SX Elbow Fitting 19.7mm diy cooling

SKU CH-HVS2-3XGH7

Connects two female G 1/4 threads at a 90° angle with 19.7 mm coated brass elbows for compact liquid-cooling loops

  • TypeCPU Block

Option UV Red

Zobrazit dalších 9 konfigurací

Přeškrtnuté varianty existují, ale zde nejsou skladem.

  • 90° turn simplifies tight-loop routing
  • Dual female G1/4 threads accept standard fittings
  • Coated brass resists corrosion in liquid loops
  • 7 mm square profile fits confined spaces
  • Single-piece elbow removes extra connection points

G 1/4 90° Elbow for Custom Loops

The PrimoChill Female-Female G 1/4 90° SX Elbow Fitting connects two male-threaded components at a right angle inside a liquid-cooling loop. Its coated brass body resists corrosion while keeping the flow path short. The 19.7 mm square profile fits tight routing channels. It is sold individually for DIY cooling builds.

Suits Builders Needing a Compact Turn

This fitting suits builders who must change tube direction by 90 degrees without adding extra tubing length. It is not for loops that require a rotary joint for alignment after tightening. Buyers who need to join more than one RevolverSX fitting should choose a different connector because the manufacturer warns against that combination.

Simple Install with Standard Threads

Installation uses the two female G 1/4 threads; screw a male fitting into each side and tighten by hand plus a quarter turn. The fixed 90° angle means the outlet orientation cannot be adjusted once sealed, so dry-fit the loop first. Over-tightening can damage the coated brass threads, which is the most common issue reported.

Přednosti

  • 90° turn simplifies tight-loop routing
  • Dual female G1/4 threads accept standard fittings
  • Coated brass resists corrosion in liquid loops
  • 7 mm square profile fits confined spaces
  • Single-piece elbow removes extra connection points

Specifikace

TypeCPU Block

Další verze tohoto modelu

Dalších 5 v této řadě

Stejná řada, jiná paměť, chladič nebo takt — porovnejte, než se rozhodnete.

Otázky k tomuto produktu

What thread size must my existing fittings have to connect to this elbow?

Both ends use female G 1/4 threads, so any male G 1/4 fitting will screw straight in.

Can I chain this 90° elbow directly to a RevolverSX fitting in the same loop?

The manufacturer warns against using more than one RevolverSX fitting with this elbow, so plan only a single RevolverSX connection.

How do I confirm the elbow is seated correctly after installation?

Check that each side measures 19.7 mm across the flats and that no coolant leaks appear when the loop is pressurised.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.