Vi tar imot kryptovaluta — slik kan kryptovalutaene du eier, kjøpe ekte maskinvare.Betal med krypto, bruk den på ekte maskinvare. Gratis, forsikret levering verden over for bestillinger over 399 $. Nøytrale kartonger uten merking, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Kursen din er låst i 30 minutter når kassen åpnes.Kurs låst i 30 minutter. Alle varer er forseglet, serienummerkontrollert og dekket av 24 måneders garanti.Forseglet, 24 måneders garanti.

Overvåkingsliste Logg inn
Three gray 75mm square GPU replacement fans with 4-pin connectors

SXDOOL

SXDOOL FD8015H12S 75mm 12V .32A 4-pin case fan 3-pack

SKU CH-1J4X-FNXJ9 MPN FD8015H12S

Three 75 mm hydraulic-bearing fans with 4-pin connectors for AMD Radeon VII cooling

  • TypeFor AMD Radeon VII cooling fan
  • Fan Size75mm
  • Bearing TypeHydraulic
  • Power Connector4 Pin
  • ColorGray
  • LEDNo
  • 75mm hydraulic-bearing fan targets AMD Radeon VII cooling
  • 12V .32A draw keeps power use low
  • 4-pin connector enables PWM speed control
  • 39mm mounting-hole spacing matches reference design
  • Three-fan pack covers multi-fan GPU layouts

Direct GPU Cooler Replacement

The SXDOOL FD8015H12S is a 75 mm hydraulic-bearing fan built specifically as a replacement cooler for the AMD Radeon VII graphics card. Each unit runs on 12 V at .32 A through a standard 4-pin connector. The pack contains three identical grey fans with no LED lighting.

Restores Original Cooling Performance

These fans replace worn or failed original coolers on the Radeon VII, restoring the airflow the card was designed around. The upgrade is worth it when the original fans develop bearing noise, vibration or reduced RPM that lets GPU temperatures climb under load. They are not suited for other graphics cards or case-mount positions.

Mounting Pattern Limits Compatibility

The 39 mm centre-to-centre mounting hole spacing and 75 mm by 15 mm frame dictate fitment; the fan will only install on coolers that match those exact dimensions. The 4-pin header provides PWM control, but the card’s firmware governs the speed curve. Buyers must verify both measurements before ordering because the same GPU model can use different coolers.

Høydepunkter

  • 75mm hydraulic-bearing fan targets AMD Radeon VII cooling
  • 12V .32A draw keeps power use low
  • 4-pin connector enables PWM speed control
  • 39mm mounting-hole spacing matches reference design
  • Three-fan pack covers multi-fan GPU layouts

Spesifikasjoner

BrandFirstD
SeriesFor AMD Radeon VII
ModelFD8015H12S
TypeFor AMD Radeon VII cooling fan
Fan Size75mm
Bearing TypeHydraulic
Power Connector4 Pin
ColorGray
LEDNo
FeaturesFor AMD Radeon VII cooling fan
Dimensions75mm
Package Contents3 pieces / set

Spørsmål om denne varen

What are the exact mounting-hole dimensions for the 75 mm frame?

The centres are spaced 39 mm apart in a square pattern, matching the original Radeon VII cooler layout.

How do I connect the 4-pin header without damaging the board?

Align the keyed notch on the plug with the tab on the graphics-card header, press straight down until it clicks, and avoid bending the delicate pins.

When should I expect to replace the hydraulic bearings?

Hydraulic bearings typically run for several years; plan a swap once you hear new rattling or notice RPM dropping under load.

Også i denne avdelingen

Kunder sammenlignet disse

Samme hylle, samme kasse — åtte mynter og 30 minutters kurslås.