Vi tar emot kryptovaluta — så att kryptot du äger kan köpa riktig hårdvara.Betala med krypto, använd det till riktig hårdvara. Fri, försäkrad frakt över hela världen vid köp över 399 $. Neutrala, omärkta ytterkartonger, skickade från Tyskland.Fri, försäkrad frakt över 399 $. Din kurs låses i 30 minuter så snart kassan öppnas.Kursen låst i 30 minuter. Varje artikel är förseglad, har kontrollerat serienummer och täcks av 24 månaders garanti.Förseglad, 24 månaders garanti.

Bevakade produkter Logga in
Three gray 75mm square GPU replacement fans with 4-pin connectors

SXDOOL

SXDOOL FD8015H12S 75mm 12V .32A 4-pin case fan 3-pack

SKU CH-1J4X-FNXJ9 MPN FD8015H12S

Three 75 mm hydraulic-bearing fans with 4-pin connectors for AMD Radeon VII cooling

  • TypeFor AMD Radeon VII cooling fan
  • Fan Size75mm
  • Bearing TypeHydraulic
  • Power Connector4 Pin
  • ColorGray
  • LEDNo
  • 75mm hydraulic-bearing fan targets AMD Radeon VII cooling
  • 12V .32A draw keeps power use low
  • 4-pin connector enables PWM speed control
  • 39mm mounting-hole spacing matches reference design
  • Three-fan pack covers multi-fan GPU layouts

Direct GPU Cooler Replacement

The SXDOOL FD8015H12S is a 75 mm hydraulic-bearing fan built specifically as a replacement cooler for the AMD Radeon VII graphics card. Each unit runs on 12 V at .32 A through a standard 4-pin connector. The pack contains three identical grey fans with no LED lighting.

Restores Original Cooling Performance

These fans replace worn or failed original coolers on the Radeon VII, restoring the airflow the card was designed around. The upgrade is worth it when the original fans develop bearing noise, vibration or reduced RPM that lets GPU temperatures climb under load. They are not suited for other graphics cards or case-mount positions.

Mounting Pattern Limits Compatibility

The 39 mm centre-to-centre mounting hole spacing and 75 mm by 15 mm frame dictate fitment; the fan will only install on coolers that match those exact dimensions. The 4-pin header provides PWM control, but the card’s firmware governs the speed curve. Buyers must verify both measurements before ordering because the same GPU model can use different coolers.

I korthet

  • 75mm hydraulic-bearing fan targets AMD Radeon VII cooling
  • 12V .32A draw keeps power use low
  • 4-pin connector enables PWM speed control
  • 39mm mounting-hole spacing matches reference design
  • Three-fan pack covers multi-fan GPU layouts

Specifikationer

BrandFirstD
SeriesFor AMD Radeon VII
ModelFD8015H12S
TypeFor AMD Radeon VII cooling fan
Fan Size75mm
Bearing TypeHydraulic
Power Connector4 Pin
ColorGray
LEDNo
FeaturesFor AMD Radeon VII cooling fan
Dimensions75mm
Package Contents3 pieces / set

Frågor om den här produkten

What are the exact mounting-hole dimensions for the 75 mm frame?

The centres are spaced 39 mm apart in a square pattern, matching the original Radeon VII cooler layout.

How do I connect the 4-pin header without damaging the board?

Align the keyed notch on the plug with the tab on the graphics-card header, press straight down until it clicks, and avoid bending the delicate pins.

When should I expect to replace the hydraulic bearings?

Hydraulic bearings typically run for several years; plan a swap once you hear new rattling or notice RPM dropping under load.

Även i den här avdelningen

Andra har jämfört dessa

Samma hylla, samma kassa — åtta mynt och ett 30-minuters kurslås.