Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
Small green development board with USB-C connector and castellated edges

LORDWORLD

LORDWORLD ESP32-H2FH4S RISC-V 32-bit 96MHz 4MB Flash development board

SKU CH-XVS6-920KW

A compact IoT development board with a RISC-V 32-bit processor at 96MHz, 4MB flash, and BLE 5 plus IEEE 802.15.4 for Zigbee 3.0 and Thread, plus castellated edges for direct soldering

  • RISC-V 32-bit core reaches 96MHz for responsive edge processing
  • 4MB flash stores firmware and data without external memory
  • BLE 5 plus IEEE 802.15.4 radio enables Zigbee 3.0 and Thread networks
  • USB Type-C connector simplifies power and debug access
  • Castellated edges allow direct soldering onto custom carrier boards

ESP32-H2FH4S RISC-V development board

The LORDWORLD ESP32-H2FH4S board uses a 32-bit single-core RISC-V processor running at up to 96MHz with 4MB of integrated Flash. It targets engineers and hobbyists building Thread, Zigbee 3.0 or BLE 5 mesh devices that need a compact module with castellated edges for direct soldering onto carrier boards.

Sustained wireless mesh operation

The chip integrates IEEE 802.15.4 radio hardware for Thread and Zigbee 3.0 alongside BLE 5, allowing long-running mesh networks without an external radio. RF performance is tuned on the module, so the board maintains link quality during continuous packet relay or sensor polling rather than only in short bursts.

Power and carrier-board checks

Verify that your carrier board supplies the voltage range required by the ESP32-H2FH4S and provides a USB-C connection for power and serial debug. Ensure the castellated pad layout matches your footprint and that your toolchain supports the RISC-V architecture with the chosen SDK for Thread or Zigbee development.

Puncte forte

  • RISC-V 32-bit core reaches 96MHz for responsive edge processing
  • 4MB flash stores firmware and data without external memory
  • BLE 5 plus IEEE 802.15.4 radio enables Zigbee 3.0 and Thread networks
  • USB Type-C connector simplifies power and debug access
  • Castellated edges allow direct soldering onto custom carrier boards

Specificații

BrandLORDWORLD

Întrebări despre acest articol

How much current does the ESP32-H2FH4S draw when the radio is active all day?

The ESP32-H2FH4S runs at up to 96 MHz with integrated BLE 5 and IEEE 802.15.4 radios; typical transmit current is in the low tens of milliamps, so a standard 5 V USB supply handles continuous operation without extra cooling.

What host connection does the Type-C port on this board require for power and programming?

The board uses a USB Type-C connector for both 5 V power and serial programming; any computer or USB charger with a Type-C or Type-A to Type-C cable will enumerate the CDC/ACM port for flashing and debug.

Can the castellated module be soldered onto a carrier board that already uses an ESP32-C3 or ESP32-S3 footprint?

The castellated edge matches the ESP32-H2FH4S module pinout only; it is not pin-compatible with ESP32-C3 or ESP32-S3 modules, so a dedicated carrier layout is required.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.