Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
Green PCB board with 24-pin ATX connector, eight Molex 4-pin and two 6-pin outputs, LED display and indicator lights

myVolts

myVolts Multiple Power Supply Adapter ATX 24 pin to 8 x Molex 4Pin & 2 x 6Pin

SKU CH-A9X2-Q7P49

Adapter board connects one ATX 24-pin source to eight Molex 4-pin and two 6-pin outputs with 12 V LED metering

  • TypeAT
  • Powers two PSUs simultaneously from a single ATX 24-pin source
  • Eight Molex 4-pin connectors plus two 6-pin outputs for graphics cards
  • Built-in voltmeter shows 12 V rail status at a glance
  • LED indicators confirm standby, power-good, +5 V and +12 V lines
  • Compact 9.4 × 9.1 cm board fits tight mining or multi-GPU builds

Multi-PSU adapter for mining rigs

This adapter board lets a single ATX 24-pin motherboard connector control two separate power supplies at once. It splits the signal into eight Molex 4-pin and two 6-pin outputs for graphics cards. A built-in LED voltmeter shows the 12 V rail while status LEDs indicate standby, power-good, 5 V and 12 V lines. The unit measures 9.4 by 9.1 cm and is aimed at multi-GPU mining configurations.

Installation and common issues

Plug the primary PSU into the Molex 4-pin female header and the secondary PSU into the 24-pin female header, then connect the 6-pin leads to each graphics card. An electronic on/off switch toggles both supplies simultaneously. The supplier stresses that connectors must be inserted in the correct orientation; reversing or offsetting a plug can damage the board. If resistance is felt, hold the socket firmly before seating the connector.

ATX signalling limits

The board simply bridges the ATX power-on signal across two PSUs and does not regulate voltage or balance current between them. Both supplies must share a common ground through the motherboard for stable operation. Total available power is capped by the lower-rated unit and by the wire gauge of the Molex and 6-pin cables. No active load-sharing or protection circuitry is present on the adapter itself.

Puncte forte

  • Powers two PSUs simultaneously from a single ATX 24-pin source
  • Eight Molex 4-pin connectors plus two 6-pin outputs for graphics cards
  • Built-in voltmeter shows 12 V rail status at a glance
  • LED indicators confirm standby, power-good, +5 V and +12 V lines
  • Compact 9.4 × 9.1 cm board fits tight mining or multi-GPU builds

Specificații

TypeAT

Întrebări despre acest articol

How do I confirm the adapter is functioning after connecting it?

The LED voltmeter shows 12 V and the four indicator lights — standby, power OK, +5 V and +12 V — will illuminate when the electronic switch turns both supplies on.

What connectors come with the unit and what must I provide?

The board includes one ATX 24 pin input, eight Molex 4 pin outputs and two 6 pin outputs; you must supply two compatible PSUs and the graphics cards.

Which version should I choose for a mining rig with multiple GPUs?

This single model provides eight Molex and two 6 pin connectors, supporting simultaneous start-up of two low-power supplies for expanded GPU power.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.