Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
Four green DDR5 UDIMM modules in static bag

NEMIX RAM

NEMIX RAM 128GB (4 x 32GB) DDR5 5600MHz CL46 1.1V 2Rx8 288-Pin Non-ECC UDIMM Kit for Supermicro X13SAE-F

SKU CH-8R06-6F9DF

A 128 GB kit of four 32 GB DDR5 modules running at 5600 MHz with CL46 latency and 1.1 V operation, validated for the Supermicro X13SAE-F motherboard

  • Capacity128GB (4 x 32GB)
  • Type288-Pin DDR5 UDIMM
  • SpeedDDR5 5600 (PC5 44800)
  • CAS LatencyCL46
  • Voltage1.10V
  • ECCNo

Size 128GB 4X32GB

  • 128 GB total capacity from four 32 GB modules for heavy multitasking
  • DDR5 5600 MT/s speed rated at PC5-44800 for fast data throughput
  • CL46 latency at 1.10 V for stable low-voltage operation
  • 2Rx8 dual-rank unbuffered UDIMM design matches Supermicro X13SAE-F memory-controller requirements
  • Built with major OEM Samsung, Micron or Hynix chips and tested for reliability

NEMIX RAM 128GB DDR5 Kit for Supermicro X13SAE-F

This 128GB kit contains four 32GB DDR5 5600MHz modules built for the Supermicro X13SAE-F motherboard. Each stick runs at 1.1V with CL46 latency in a 2Rx8 unbuffered UDIMM layout. The 288-pin DIMMs use major OEM chips from Samsung, Micron, or Hynix and ship without heat spreaders.

Suits builders filling all four slots

Buyers who need ECC error correction or registered modules should look elsewhere, as this kit is non-ECC and unbuffered. Systems limited to lower memory speeds or different voltage requirements will not match the rated 5600MHz CL46 specification. Anyone needing a smaller capacity upgrade should consider a different kit.

Simple installation with standard UDIMM alignment

The 288-pin modules insert directly into the motherboard DIMM slots following the board's population order. Most issues arise when the BIOS is not updated to support the full 128GB capacity or when modules are placed in the wrong slot sequence. Verify the manual for approved DIMM population rules before fitting the kit.

Puncte forte

  • 128 GB total capacity from four 32 GB modules for heavy multitasking
  • DDR5 5600 MT/s speed rated at PC5-44800 for fast data throughput
  • CL46 latency at 1.10 V for stable low-voltage operation
  • 2Rx8 dual-rank unbuffered UDIMM design matches Supermicro X13SAE-F memory-controller requirements
  • Built with major OEM Samsung, Micron or Hynix chips and tested for reliability

Specificații

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR5 Non-ECC Unbuffered UDIMM Memory
Part NumberMD44800-328K4
Capacity128GB (4 x 32GB)
Type288-Pin DDR5 UDIMM
SpeedDDR5 5600 (PC5 44800)
CAS LatencyCL46
Voltage1.10V
ECCNo
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 Non-ECC Unbuffered UDIMM Motherboard Compatible
Package Content128GB 4X32GB DDR5 5600MHz PC5-44800 2Rx8 1.1V 288-PIN Non-ECC UDIMM KIT

Alte versiuni ale acestui model

5 în plus din aceeași gamă

Aceeași familie, memorie, radiator sau frecvență diferite — comparați înainte de a vă decide.

Întrebări despre acest articol

Does my motherboard need four DDR5 UDIMM slots to install this 128GB kit?

Yes, the kit contains four 32GB modules, so the board must provide four 288-pin DDR5 UDIMM slots to use the full 128GB capacity.

Can I keep my existing DDR5 modules and add this kit to reach a higher total?

Only if the board supports mixing 2Rx8 CL46 1.10V modules with your current memory; the manual will confirm approved population rules and maximum capacity.

How do I verify the kit is running at DDR5 5600 CL46 after installation?

Check the memory speed and timings in the BIOS or a system-information tool — they should show 5600 MT/s and CL46 at 1.10V.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.