Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
Square black 60mm fan with 4-pin connector

OEM Industries

OEM Industries CHD6012EB-AH(RE) 60mm 12V 0.3A 4 Pin Ball Bearing Fan

SKU CH-C5H5-1JHCY

A 60mm ball-bearing fan with a 4-pin connector runs on 12V at 0.3A for targeted CPU cooling

  • ColorBlack
  • TypeFan only
  • Fan Size60mm
  • Bearing TypeBall
  • Power Connector4 Pin
  • LEDNo
  • 60 mm frame fits tight case layouts
  • ball bearing runs quietly for long service life
  • 4 pin connector enables PWM speed control
  • 12 V .3 A draws minimal power from the rail
  • black finish matches most build colour schemes

Compact 60 mm fan for tight builds

The OEM Industries CHD6012EB-AH(RE) is a 60 mm square cooler designed for small-form-factor cases and low-profile CPU coolers. It runs on 12 V and draws 0.3 A through a standard four-pin connector, so motherboard PWM control works out of the box. The ball-bearing motor targets longer life in continuous operation.

Ball bearing and four-pin control

Ball bearings reduce wear compared with sleeve designs, helping the fan maintain consistent speed over extended use. The four-wire header enables automatic speed curves tied to CPU temperature, keeping noise lower at idle while delivering full airflow under load. No LEDs are fitted, making the unit suitable for professional or stealth builds.

Replaces noisy or failed 60 mm coolers

This fan fits existing 60×20 mm mounts, so it can refresh an ageing heatsink or a cramped chassis fan slot without adapter brackets. The upgrade is worthwhile when the original unit develops bearing rattle or cannot spin fast enough for modern thermal loads. Buyers needing higher static pressure for dense radiators or larger frame sizes should look elsewhere.

Puncte forte

  • 60 mm frame fits tight case layouts
  • ball bearing runs quietly for long service life
  • 4 pin connector enables PWM speed control
  • 12 V .3 A draws minimal power from the rail
  • black finish matches most build colour schemes

Specificații

ModelCHD6012EB-AH(RE)
ColorBlack
TypeFan only
Fan Size60mm
Bearing TypeBall
Power Connector4 Pin
LEDNo

Întrebări despre acest articol

What does the 4-pin connector allow this 60 mm fan to do that a 3-pin cannot?

The fourth wire carries a PWM signal so the motherboard can vary the 12 V 0.3 A motor speed precisely instead of only varying voltage.

Will the 60 mm by 20 mm frame fit a standard 60 mm mounting pattern?

Yes, the 6020 square frame uses the common 60 mm hole spacing, but verify your case or cooler has 20 mm clearance for the thicker body.

How do I install the CHD6012EB-AH(RE) so the ball bearing stays quiet?

Mount the fan with the four screws through the corner holes, orient the airflow arrow toward the heatsink, and plug the 4-pin header in fully so the PWM wire makes contact.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.