Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Compact rectangular air-assist pump unit in plastic and metal finish with hose and nozzle attached

ACMER

ACMER C4 Air Assist Pump Kit 30L/min Adjustable 0-0.3MPa

SKU CH-TF2X-ETTDN

Adjustable 0–0.3 MPa air assist clears smoke, shields the lens and cools cuts at under 40 dB

  • Delivers 30 L/min airflow to clear smoke and dust
  • Adjustable 0–0.3 MPa pressure suits varied materials
  • Operates below 40 dB for a quiet workspace
  • Protects the laser lens from residue buildup
  • Works with 110 V and 220 V supplies

Air Assist for Laser Cutting

The ACMER C4 Air Assist Pump Kit mounts to a laser cutter or engraver and blows a focused stream of air across the work area. It clears smoke and dust while shielding the lens from debris. The adjustable airflow runs from 0 to 0.3MPa, reaching 30L/min at 220V or 28L/min at 110V. Operation stays below 40dB.

Suited for Precision Work; Not for Automated Control

Makers who need cleaner cuts on wood or acrylic and want to reduce surface charring will benefit from the steady airflow. The kit includes hose, nozzle, power adapter and manual for quick setup. Builders who require automatic on/off switching synced to the laser controller cannot use this pump, because it only supports manual airflow adjustment.

30L/min Airflow with Adjustable Pressure

At full pressure the pump moves 30L/min, enough to keep the cut zone clear on most desktop laser beds and to lower the surface temperature during long passes. The 0.3MPa ceiling limits penetration on very thick or dense stock where higher pressure would be needed. The unit measures 145 by 135 by 70mm and runs on AC110V/220V power.

Poudarki

  • Delivers 30 L/min airflow to clear smoke and dust
  • Adjustable 0–0.3 MPa pressure suits varied materials
  • Operates below 40 dB for a quiet workspace
  • Protects the laser lens from residue buildup
  • Works with 110 V and 220 V supplies

Specifikacije

BrandACMER
ModelC4

Vprašanja o tem izdelku

What power supply does the ACMER C4 air assist pump need to operate?

The pump runs on AC 110 V or 220 V mains power via the included adapter; it does not draw power from the laser engraver itself.

Will the 30 L/min airflow and adjustable 0-0.3 MPa pressure work with an older laser cutter that has a smaller nozzle?

Yes — the pressure knob lets you dial the flow down to suit smaller nozzles, while the 30 L/min maximum still clears smoke from larger beds.

How can I confirm the unit is running correctly once connected?

Check that the pressure gauge shows your chosen setting between 0 and 0.3 MPa and listen for the quiet hum below 40 dB; steady airflow at the nozzle means it is working.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.