Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Silver 90-degree rigid-tube fitting for 14mm OD tubing, brass construction

Bitspower

Bitspower BP-E90DML14 14mm 90° rigid-tube fitting

SKU CH-9577-KPWWB MPN BP-E90DML14

A 90-degree rigid-tube fitting that joins two 14mm hard tubes for custom water-cooling loops

  • TypeFittings
  • Designed for dual multi-link extension with 14mm OD rigid tubing on both sides
  • 90-degree angle enables tight routing in compact liquid-cooling loops
  • True Hi-Flow design minimises restriction for efficient coolant circulation
  • Precision-machined from high-quality brass for durability and corrosion resistance
  • Silver Shining finish matches premium loop aesthetics

Purpose-built rigid-tube connector

The Bitspower BP-E90DML14 is a 90-degree fitting engineered for 14mm OD hard tubing. It joins two tube runs at a right angle inside a custom liquid-cooling loop. The coupler is machined from brass with a silver finish and is validated only for Bitspower rigid tubing.

Flow-oriented thermal path

A true hi-flow internal profile minimises restriction so coolant moves freely through the bend. Reduced pressure drop helps the pump maintain steady flow rates without extra power draw. The all-metal construction adds no plastic degradation risk over long-term thermal cycling.

System-level integration

The dual multi-link design lets builders extend a run in two directions from a single 90-degree joint. This reduces the total number of separate fittings required for complex routing. Compatibility is limited to Bitspower 14mm OD hard tube, so mixed-brand tubing cannot be used.

Poudarki

  • Designed for dual multi-link extension with 14mm OD rigid tubing on both sides
  • 90-degree angle enables tight routing in compact liquid-cooling loops
  • True Hi-Flow design minimises restriction for efficient coolant circulation
  • Precision-machined from high-quality brass for durability and corrosion resistance
  • Silver Shining finish matches premium loop aesthetics

Specifikacije

TypeFittings

Vprašanja o tem izdelku

How do I install the Bitspower BP-E90DML14 fitting onto 14mm rigid tubing, and what step is often missed?

Cut the tube square, chamfer the edge, slide the compression nut and olive onto the tube, then seat the tube fully against the fitting stop before tightening the nut by hand plus a quarter turn; the step often missed is confirming full insertion past the O-ring before final torque.

What maintenance or replacement will the Bitspower BP-E90DML14 fitting need over time?

Inspect the O-rings annually for hardening or flattening; replace them if a slow leak appears or during a loop drain. The brass body and silver finish do not require replacement unless physically damaged.

At what point does the 90-degree angle of the Bitspower BP-E90DML14 become the flow-limiting factor under sustained use?

The 90-degree bend introduces the primary restriction in the loop; its true Hi-Flow design minimises turbulence, but the sharp directional change remains the first hydraulic limit before tubing length or other fittings.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.