Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Ten silver aluminium heatsinks, 20 by 20 by 6 millimetres, finned extrusion

EN-Labs

EN-Labs Aluminium Heatsink 20x20x6mm 10pcs Silver

SKU CH-BJD9-8QF3X

Pack of ten 20×20×6 mm aluminium heatsinks for MOSFETs, voltage regulators and other ICs, 35 g total

  • ColorSilver
  • CompatibilityMotherboard Chipsets
  • MaterialAluminium
  • FeaturesProduct Description Aluminum IC heatsink for power transisto
  • Dimensions20mm x 20mm x 6mm
  • Dissipates heat from power transistors, FETs and ICs
  • Fits voltage regulators, MOSFETs and SCRs with 20mm footprint
  • Extruded aluminium fins increase surface area for passive cooling
  • Ten-piece pack covers multiple components on a board
  • Light 35g weight adds minimal mass to assemblies

Compact Aluminium Heatsink Pack

This pack contains 10 silver aluminium heatsinks measuring 20mm by 20mm by 6mm. They are designed for DIY cooling of motherboard chipsets and similar components. Each unit weighs 35g and features extruded fins for heat dissipation. Adhesive glue is required for installation and is not included.

Hobbyists Replacing Small Chip Coolers

The heatsinks suit builders replacing stock coolers on MOSFETs, voltage regulators, SCRs or power transistors. They are not suited for buyers who need larger surface areas for high-power CPUs or GPUs. Installers without thermal adhesive or those needing pre-applied pads should look elsewhere.

Ten Units Cover Multiple Board Components

Ten pieces provide enough headroom for several chipsets or power-stage clusters on a single board. The 6mm profile fits tight clearances around dense layouts. Thermal limits appear once sustained loads exceed the small fin area's dissipation capacity.

Poudarki

  • Dissipates heat from power transistors, FETs and ICs
  • Fits voltage regulators, MOSFETs and SCRs with 20mm footprint
  • Extruded aluminium fins increase surface area for passive cooling
  • Ten-piece pack covers multiple components on a board
  • Light 35g weight adds minimal mass to assemblies

Specifikacije

ColorSilver
CompatibilityMotherboard Chipsets
MaterialAluminium
FeaturesProduct Description Aluminum IC heatsink for power transistor, FET, IC, power amplifier, Voltage Regulator, MOSFET, SCR, etc
Use heatsink adhesive glue to install heatsink on the IC.Glue is not included here.
Size is 20x20x6mm,Please check your component dimension carefully,and make sure size of the heatsink fits it no problem.
Specification
Product Name: Heatsink
Material: Aluminium
Color: Silver Tone
Overall Size: 20mm x 20mm x 6mm
Weight: 35g
Package Content: 10pcs x Heatsink
Dimensions20mm x 20mm x 6mm

Vprašanja o tem izdelku

What adhesive do I need to attach these 20mm heatsinks to my MOSFETs?

You must supply heatsink adhesive glue; none is included in the 10-piece pack.

Will these 6mm-tall sinks clear the tall capacitors on an older motherboard chipset?

At 6 mm overall height they sit low, but measure your board's capacitor clearance before fitting.

How can I verify each aluminium sink is making good contact after gluing?

Check that the 20 x 20 mm base sits flat on the IC with no visible gaps and monitor component temperatures under load.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.