Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Transparent 3.0 mm filament spool, 0.25 kg, water-soluble support material

Lay Filaments

Lay Filaments Lay-Cloud Dissolvable Support Filament 3.0mm 0.25kg

SKU CH-83R3-AE1H9

Water-soluble support filament for flexible materials, 2.85 mm diameter, 0.25 kg spool, prints at 230-240 °C

  • Water-soluble support dissolves in cold or hot water without damaging the print
  • Designed for flexible filaments like TPE to enable complex overhangs
  • ±0.1 mm diameter tolerance ensures consistent extrusion at 230–240 °C
  • 25 kg spool of 2.85 mm filament compatible with dual-extruder printers
  • Lay-Away series material leaves no residue after dissolution

Dissolvable Support for Flexible Filaments

Lay Filaments Lay-Cloud is a water-soluble support material engineered specifically for use with flexible and semi-flexible filaments such as TPE. It requires a dual-extruder 3D printer to print support structures alongside the primary model material.

Upgrade from Breakaway Supports

This filament replaces mechanical removal methods that can tear or mark delicate flexible prints. The switch is worth it when printing complex geometries with overhangs or internal cavities where physical support removal would damage the final piece.

0.25 kg Spool Capacity

The 2.85 mm diameter filament with ±0.1 mm tolerance prints at 230 to 240 °C and dissolves fully in cold or hot water within hours. The small spool suits occasional flexible prints but runs out quickly during high-volume production runs.

Poudarki

  • Water-soluble support dissolves in cold or hot water without damaging the print
  • Designed for flexible filaments like TPE to enable complex overhangs
  • ±0.1 mm diameter tolerance ensures consistent extrusion at 230–240 °C
  • 25 kg spool of 2.85 mm filament compatible with dual-extruder printers
  • Lay-Away series material leaves no residue after dissolution

Specifikacije

BrandLay Filaments

Vprašanja o tem izdelku

Will the 2.85 mm filament with ±0.1 mm tolerance feed reliably in my 3.0 mm Bowden tube?

Yes — the 2.85 mm diameter and ±0.1 mm tolerance are within the standard range for 3.0 mm Bowden systems, so the filament feeds without binding.

What nozzle temperature and water temperature should I use to print and dissolve Lay-Cloud supports?

Print at 230-240 °C; after printing, soak the part in cold or hot water for a few hours — hot water dissolves the support faster, but cold water also works.

How often will I need to replace the 0.25 kg spool when printing flexible parts with dual extrusion?

A 0.25 kg spool lasts for many small-to-medium flexible prints; replace it when the filament runs out or if moisture makes the water-soluble material sticky.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.