Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Grey ATX power supply unit with single fan and reduced depth

Replace Power

Replace Power RPSU-C99-67 power supply

SKU CH-T7AW-181FX MPN RPSU-C99-67

ATX power supply with one SATA connector and 80 mm cooling fan, switchable 115/230 V input and reduced depth for legacy eMachines systems

  • ColorGrey
  • TypeATX
  • Fans1
  • Weight2.5
  • Replaces several legacy eMachines power supplies
  • Switchable 115 / 230 V input voltage
  • Reduced depth 5.9" height x 3.4" width for compatibility
  • Over current, over power and over voltage protection
  • Includes SATA, ATX, 12V ATX and LP4 connectors

Replacement PSU for Legacy eMachines

This Replace Power RPSU-C99-67 unit serves as a direct power-supply replacement for older eMachines desktops including the S2485, T1930, T1140, H3054, H2862 and T1782 models. It fits standard ATX bays and uses a grey enclosure with a single 80 mm fan for cooling. The reduced depth helps it sit in tighter chassis where longer units would not fit. It is intended for owners restoring or repairing those specific legacy systems.

Selectable 115 V or 230 V Input

The unit operates on either 115 V or 230 V mains voltage, selected by a physical switch on the rear. This dual-voltage capability lets the same PSU work in regions with different grid standards without needing a separate model. Builders must verify the switch matches the local supply before powering the system. Incorrect setting will prevent operation or damage the unit.

Connector Mix for Older Builds

The harness provides one SATA connector, one 20-pin ATX motherboard plug, one 12 V ATX plug, two large peripheral connectors and two 6-inch small peripheral connectors. This combination covers the drive and board interfaces common in the target eMachines era. Systems requiring multiple SATA devices, PCIe power or a 24-pin motherboard header will find the native cabling insufficient.

Poudarki

  • Replaces several legacy eMachines power supplies
  • Switchable 115 / 230 V input voltage
  • Reduced depth 5.9" height x 3.4" width for compatibility
  • Over current, over power and over voltage protection
  • Includes SATA, ATX, 12V ATX and LP4 connectors

Specifikacije

BrandReplace Power
ModelRPSU-C99-67
ColorGrey
TypeATX
Fans1
Weight2.5

Vprašanja o tem izdelku

What does the 67 W label on the RPSU-C99-67 mean for my eMachines desktop?

The 67 W figure is the model identifier; the unit is a standard ATX replacement rated for 115 V or 230 V input and supplies power through one SATA, one 20+4 pin ATX, one 12 V ATX, two large peripheral and one small peripheral connector.

Which ATX power standard does the 20+4 pin connector follow?

The 20+4 pin motherboard plug and the separate 12 V ATX plug are standard ATX connectors compatible with the eMachines S2485, T1930, T1140, H3054, H2862 and T1782 models listed.

Will the 5.9 inch by 3.4 inch grey chassis fit my existing case mounting points?

The reduced-depth design measures 5.9 inches high by 3.4 inches wide and uses a single 80 mm fan, matching the mounting pattern of the legacy eMachines units it replaces.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.