Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Silver 170mm case fan with four-wire connector and ball bearing

SunnyStar Co., Ltd

SunnyStar Co., Ltd 175R-069D-0566 170mm 24V 3.5A 4Wire Case Fan

SKU CH-Y4Z6-40NFD

A 170 mm ball-bearing case fan running at 24 V and 3.5 A with a four-wire PWM connector for Mitsubishi inverter systems

  • TypeCase Fan
  • Fan Size170mm
  • Bearing TypeBall
  • Power Connector4 Wires
  • ColorSilver
  • LEDNon-LED
  • 170 mm diameter moves more air per rotation
  • 24 V 3.5 A rating matches Mitsubishi inverter specs
  • 4-wire PWM connector enables precise speed control
  • Ball bearing design reduces friction for longer life
  • 17 cm silver frame fits standard 170 mm mounting points

Industrial-grade 170 mm fan for Mitsubishi inverters

This 170 mm case fan is built to the 175R-069D-0566 specification and operates on a 24 V supply drawing 3.5 A. It targets engineers and integrators who need a direct replacement for Mitsubishi inverter cooling assemblies. The four-wire connector provides PWM control and tachometer feedback for precise speed regulation.

Ball-bearing thermals with PWM speed control

The ball bearing design sustains continuous operation at the rated 24 V input without sleeve-bearing wear. PWM signalling on the fourth wire allows the host system to match airflow to thermal load, reducing acoustic output when full speed is unnecessary. Power draw remains at 3.5 A only when the inverter demands maximum cooling capacity.

Four-wire harness enables closed-loop monitoring

The bundled 4-wire harness delivers power, ground, PWM input and RPM output in a single connector, eliminating the need for separate sensor wiring. This lets the inverter controller verify fan health in real time and trigger alerts if speed drops below threshold. No additional software, lighting controllers or mounting brackets are included.

Poudarki

  • 170 mm diameter moves more air per rotation
  • 24 V 3.5 A rating matches Mitsubishi inverter specs
  • 4-wire PWM connector enables precise speed control
  • Ball bearing design reduces friction for longer life
  • 17 cm silver frame fits standard 170 mm mounting points

Specifikacije

Series175R-069D-0566
Model175R-069D-0566
TypeCase Fan
Fan Size170mm
Bearing TypeBall
Power Connector4 Wires
ColorSilver
LEDNon-LED
Dimensions17CM

Vprašanja o tem izdelku

How do I connect the 4-wire power connector to a 24 V supply, and what is the common polarity mistake?

Match the 4-wire lead to the inverter’s 24 V header; the yellow wire carries the PWM signal and must not be swapped with the red 24 V line.

Which part of the 170 mm ball-bearing fan wears out first and needs replacement?

The ball bearing assembly inside the 175R-069D-0566 rotor is the service item; when noise or vibration appears the whole fan unit is replaced.

At what current draw does the 24 V 3.5 A motor hit its thermal limit during continuous operation?

The motor is rated for 3.5 A at 24 V; sustained operation at that current is the design limit before overtemperature protection activates.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.