Sprejemamo kriptovalute — tako lahko sredstva, ki jih imate, kupijo pravo strojno opremo.Plačajte v kriptovaluti, zapravite jo za pravo strojno opremo. Brezplačna zavarovana dostava po vsem svetu nad 399 $. Nevtralni kartoni brez znamke, poslani iz Nemčije.Brezplačna zavarovana dostava nad 399 $. Vaš tečaj je zaklenjen za 30 minut, takoj ko se odpre blagajna.Tečaj zaklenjen 30 minut. Vsak izdelek je zapečaten, njegova serijska številka preverjena, in krit z 24-mesečno garancijo.Zapečateno, 24-mesečna garancija.

Spremljani izdelki Prijava
Green 3D printing filament spool, 2.85 mm diameter, 1 kg weight

Taulman 3D

Taulman 3D In-PLA Filament 2.85mm 1kg Green

SKU CH-8HKX-9959W

Green 2.85 mm PLA filament on a 1 kg spool prints at 217–222 °C with 70 °C bed and offers 10 043 psi tensile strength and 497 % elongation

  • ColorGreen
  • TypeFilament
  • Stronger prints with 10,000 psi tensile strength
  • Better colour and clarity than standard PLA
  • High 497% elongation resists mechanical stress
  • Improved heat deflection handles thermal stress
  • Prints at 217-222 °C nozzle and 70 °C bed

Filament for functional prints

Taulman 3D In-PLA is a 2.85 mm industrial PLA supplied on a 1 kg spool in green. It targets makers who need higher tensile strength and elongation than standard PLA for mechanical parts. The material suits collectibles, figurines, phone cases and electronic enclosures. It prints at 217C to 222C with a bed at 70C.

Consistent 2.85 mm diameter

The filament holds a tight 2.85 mm tolerance so it feeds reliably in Bowden and direct-drive extruders without grinding. Green pigment stays uniform across the spool for predictable colour matching between prints. No special bed surface or enclosure is required beyond the stated bed temperature. The spool fits standard holders and stores easily.

10,000 psi tensile strength

In-PLA reaches a tensile strength of 10,000 psi and an elongation of 497%, far above baseline PLA. That combination lets printed parts absorb impact and flex before breaking. Heat deflection temperature is also raised, so finished items resist warping in warm environments. Choose this filament when mechanical and thermal stress are both factors.

Poudarki

  • Stronger prints with 10,000 psi tensile strength
  • Better colour and clarity than standard PLA
  • High 497% elongation resists mechanical stress
  • Improved heat deflection handles thermal stress
  • Prints at 217-222 °C nozzle and 70 °C bed

Specifikacije

Brandtaulman3d
ColorGreen
TypeFilament

Vprašanja o tem izdelku

What print-temperature range does the 2.85 mm In-PLA filament require?

The recommended nozzle temperature is 217C to 222C, with a heated bed at 70C for best adhesion.

What spool diameter and mounting style does the 1 kg Green spool use?

The filament is supplied on a standard 1 kg spool with a centre hole that fits most common 3D-printer holders.

How do I load the 2.85 mm filament without causing a jam?

Heat the hot-end to 217C–222C, cut the tip at a clean angle, and feed it straight into the extruder until the drive gear grips; forcing it cold is the common mistake.

Tudi v tem oddelku

Stranke so primerjale tudi te

Ista polica, ista blagajna — osem kriptovalut in 30-minutni zaklep tečaja.