Silver metal rectangular server power supply unit with handle and ventilation grille

Athena Power

Athena Power AP-RRP4ATX6808 800W redundant server power supply

SKU CH-8S9K-4BPT6 MPN AP-RRP4ATX6808

An 800W redundant server power supply with 20+4Pin main connector and 80 PLUS Bronze efficiency

Single/RedundantRedundant
Maximum Power800W
Main Connector20+4Pin
Output Current+5V@24A, +12V x [email protected] , +3.3V@24A, -5V@0A, [emai
Input Voltage88 -264 Volts Ac
Input Frequency Range47 - 63 Hz

Maximum Power 800W

500W
800W

800W redundant design keeps servers running during a module failure
80 PLUS Bronze efficiency reduces energy waste and heat output
88–264 V AC input works worldwide without a voltage switch
100,000-hour MTBF at 25 °C indicates long-term reliability
Compact 5.9″ × 3.4″ × 8.9″ form factor fits dense rack chassis

596,99 щ.д.

0.00762761 BTC по днешния курс

В наличност · изпраща се днес

На касата курсът се заключва за 30 минути.

Доставка до Съединени щати ориентировъчно

UPS Worldwide Expedited 3–6 работни дни Безплатно
DHL Express Worldwide 2–3 работни дни 74,90 щ.д.

Вносните мита се начисляват от Вашата държава при пристигане.

Доставка на друг адрес

800W redundant server supply

The Athena Power AP-RRP4ATX6808 is an 800 watt redundant power supply built for rack servers that require continuous uptime. It fits standard 20+4 pin ATX motherboards and accepts 88 to 264 volt AC input at 47 to 63 Hz. The unit carries 80 PLUS Bronze certification and is rated for 100,000 hours MTBF at full load and 25 °C.

Redundant 800W headroom

Two hot-swap modules share the load so a single module failure does not interrupt operation. The +12 volt rail delivers up to 30 amps while +5 volt and +3.3 volt rails each provide 24 amps. Maximum combined output is 800 watts; sustained loads above that will trip protection. Hold-up time is at least 20 ms at nominal input.

Compact redundant build

The supply measures 5.9 by 3.4 by 8.9 inches and weighs 9.0 lbs, matching common redundant PSU bays. Dielectric withstand is tested at 1800 volts AC primary to frame ground. Operating temperature range is 5 °C to 40 °C at 250 watt load or -10 °C to 50 °C at 220 watt load. Not suited for builds needing higher single-rail current or non-redundant form factors.

Акценти

800W redundant design keeps servers running during a module failure
80 PLUS Bronze efficiency reduces energy waste and heat output
88–264 V AC input works worldwide without a voltage switch
100,000-hour MTBF at 25 °C indicates long-term reliability
Compact 5.9″ × 3.4″ × 8.9″ form factor fits dense rack chassis

Спецификации

Brand	Athena Power
Model	AP-RRP4ATX6808
Single/Redundant	Redundant
Maximum Power	800W
Main Connector	20+4Pin
Output Current	+5V@24A, +12V x [email protected] , +3.3V@24A, -5V@0A, [email protected] , +5V-SB@4A
Input Voltage	88 -264 Volts Ac
Input Frequency Range	47 - 63 Hz
MTBF	100,000 Hours on Maximum Load at +25°C
Hold-up Time	20ms Minimum at Nominal Input Voltage
Features	Dielectric Withstand: Primary Frame Ground 1800V AC for 1 Second Rise time: 50ms maximum
Dimensions	5.9" x 3.4" x 8.9"
Weight	9.0 lbs.
Humidity	90% on Operating, 95% on Storage
Temperature	Operating +5° C ~ +40° C on 250W Output Load or -10° C ~ +50° C on 220W Output Load
Тегло на пратката	5.25 kg
Размери на опаковката	290 × 254 × 193 mm

Други версии на този модел

1 още от същата серия

Същото семейство, различна памет, охладител или честота — сравнете, преди да решите.

Athena Power

Athena Power AP-RRP4ATX6508 2 x 500W redundant server power supply

EPS12V
Redundant

393,99 щ.д.

0.00503392BTC

В наличност

Въпроси за този артикул

Will the 20+4Pin main connector and 800W output work with my older ATX motherboard that uses a 20-pin socket?

The 20+4Pin connector splits so the 20-pin section fits legacy ATX boards while the 800W capacity provides ample headroom for older components.

How can I verify the redundant modules are both active after installation?

Each module has its own AC inlet and status LED; both LEDs lit green confirm both units are sharing the load.

Does the package include the IEC power cords for each module or must I buy them separately?

The unit ships with the redundant power-supply modules installed in the chassis; IEC cords for the dual inlets are not included and must be sourced separately.

Още от този рафт