Aceitamos criptomoeda — para que as moedas que detém possam comprar material informático real.Pague em cripto, gaste-a em material informático real. Envio seguro gratuito para todo o mundo acima de 399 $. Caixas neutras, sem marca, expedidas a partir da Alemanha.Envio seguro gratuito acima de 399 $. A sua taxa fica bloqueada durante 30 minutos assim que abre a finalização da compra.Taxa bloqueada 30 minutos. Cada artigo é selado, o seu número de série é verificado, e está coberto por uma garantia de 24 meses.Selado, garantido 24 meses.

Artigos guardados Iniciar sessão
Silver metal rectangular server power supply unit with handle and ventilation grille

Athena Power

Athena Power AP-RRP4ATX6808 800W redundant server power supply

SKU CH-8S9K-4BPT6 MPN AP-RRP4ATX6808

An 800W redundant server power supply with 20+4Pin main connector and 80 PLUS Bronze efficiency

  • Single/RedundantRedundant
  • Maximum Power800W
  • Main Connector20+4Pin
  • Output Current+5V@24A, +12V x [email protected] , +3.3V@24A, -5V@0A, [emai
  • Input Voltage88 -264 Volts Ac
  • Input Frequency Range47 - 63 Hz

Maximum Power 800W

  • 800W redundant design keeps servers running during a module failure
  • 80 PLUS Bronze efficiency reduces energy waste and heat output
  • 88–264 V AC input works worldwide without a voltage switch
  • 100,000-hour MTBF at 25 °C indicates long-term reliability
  • Compact 5.9″ × 3.4″ × 8.9″ form factor fits dense rack chassis

800W redundant server supply

The Athena Power AP-RRP4ATX6808 is an 800 watt redundant power supply built for rack servers that require continuous uptime. It fits standard 20+4 pin ATX motherboards and accepts 88 to 264 volt AC input at 47 to 63 Hz. The unit carries 80 PLUS Bronze certification and is rated for 100,000 hours MTBF at full load and 25 °C.

Redundant 800W headroom

Two hot-swap modules share the load so a single module failure does not interrupt operation. The +12 volt rail delivers up to 30 amps while +5 volt and +3.3 volt rails each provide 24 amps. Maximum combined output is 800 watts; sustained loads above that will trip protection. Hold-up time is at least 20 ms at nominal input.

Compact redundant build

The supply measures 5.9 by 3.4 by 8.9 inches and weighs 9.0 lbs, matching common redundant PSU bays. Dielectric withstand is tested at 1800 volts AC primary to frame ground. Operating temperature range is 5 °C to 40 °C at 250 watt load or -10 °C to 50 °C at 220 watt load. Not suited for builds needing higher single-rail current or non-redundant form factors.

Pontos fortes

  • 800W redundant design keeps servers running during a module failure
  • 80 PLUS Bronze efficiency reduces energy waste and heat output
  • 88–264 V AC input works worldwide without a voltage switch
  • 100,000-hour MTBF at 25 °C indicates long-term reliability
  • Compact 5.9″ × 3.4″ × 8.9″ form factor fits dense rack chassis

Especificações

BrandAthena Power
ModelAP-RRP4ATX6808
Single/RedundantRedundant
Maximum Power800W
Main Connector20+4Pin
Output Current+5V@24A, +12V x [email protected] , +3.3V@24A, -5V@0A, [email protected] , +5V-SB@4A
Input Voltage88 -264 Volts Ac
Input Frequency Range47 - 63 Hz
MTBF100,000 Hours on Maximum Load at +25°C
Hold-up Time20ms Minimum at Nominal Input Voltage
FeaturesDielectric Withstand: Primary Frame Ground 1800V AC for 1 Second
Rise time: 50ms maximum
Dimensions5.9" x 3.4" x 8.9"
Weight9.0 lbs.
Humidity90% on Operating, 95% on Storage
TemperatureOperating +5° C ~ +40° C on 250W Output Load or -10° C ~ +50° C on 220W Output Load
Peso de envio5.25 kg
Dimensões da embalagem290 × 254 × 193 mm

Outras versões deste modelo

Mais 1 nesta gama

Mesma família, memória, ventoinha ou frequência diferentes — compare antes de decidir.

Perguntas sobre este artigo

Will the 20+4Pin main connector and 800W output work with my older ATX motherboard that uses a 20-pin socket?

The 20+4Pin connector splits so the 20-pin section fits legacy ATX boards while the 800W capacity provides ample headroom for older components.

How can I verify the redundant modules are both active after installation?

Each module has its own AC inlet and status LED; both LEDs lit green confirm both units are sharing the load.

Does the package include the IEC power cords for each module or must I buy them separately?

The unit ships with the redundant power-supply modules installed in the chassis; IEC cords for the dual inlets are not included and must be sourced separately.

Também nesta secção

Os clientes também compararam

Mesma prateleira, mesma finalização da compra — oito moedas e uma taxa bloqueada durante 30 minutos.