Приемаме криптовалута — така монетите, които притежавате, могат да купят истински хардуер.Платете с крипто, похарчете го за истински хардуер. Безплатна застрахована доставка по целия свят над 399 $. Неутрални кашони без марка, изпратени от Германия.Безплатна застрахована доставка над 399 $. Курсът Ви е заключен за 30 минути веднага след отварянето на касата.Курс, заключен за 30 минути. Всеки артикул е запечатан, серийният му номер е проверен, и е покрит с 24-месечна гаранция.Запечатан, 24-месечна гаранция.

Проследени артикули Вход
Four square sheets of blue build-plate tape 12.1 inches each side

MakerBot

MakerBot MP06626 Build Plate Tape 4-Pack 12.1" x 12.1" Z18

SKU CH-WBNN-J5VYE MPN MP06626

Four sheets of 12.1-inch square build-plate tape sized for the MakerBot Replicator Z18

  • TypeBuild Plate Tape
  • SpecificationQuantity: 4-Pack Compatibility: MakerBot Replicator Z18 3D P
  • Four sheets ready for immediate bed changes
  • Each sheet measures 12.1" x 12.1" for full coverage
  • Designed specifically for the Replicator Z18 3D printer
  • Smooth surface promotes reliable first-layer adhesion
  • Packaged new as model MP06626 from MakerBot

Build Plate Tape for Z18

This four-pack of adhesive sheets is made for the MakerBot Replicator Z18 3D printer. Each sheet measures 12.1" x 12.1" to match the printer's build surface. The tape provides a textured layer that helps first-layer adhesion during printing. Users replace sheets when the surface wears or becomes damaged.

Replaces worn factory sheets

The tape substitutes the original build plate covering supplied with the Z18. A fresh sheet restores consistent adhesion without requiring bed levelling changes. The jump is worth it when prints start lifting at the corners or the existing tape shows deep gouges. Four sheets give multiple refreshes before reordering.

Suits Z18 owners needing quick swaps

Operators who run frequent jobs and want minimal downtime will value the pre-cut dimensions. Shops without a Z18 cannot use these sheets because the size is specific to that model. Buyers needing a different dimensions or a permanent build surface should look at other options.

Акценти

  • Four sheets ready for immediate bed changes
  • Each sheet measures 12.1" x 12.1" for full coverage
  • Designed specifically for the Replicator Z18 3D printer
  • Smooth surface promotes reliable first-layer adhesion
  • Packaged new as model MP06626 from MakerBot

Спецификации

BrandMakerbot
ModelMP06626
TypeBuild Plate Tape
SpecificationQuantity: 4-Pack
Compatibility: MakerBot Replicator Z18 3D Printer
Dimension: 12.1" x 12.1 (W x L)
Тегло на пратката0.23 kg
Размери на опаковката368 × 241 × 25 mm

Въпроси за този артикул

What are the exact dimensions of each tape sheet so I can confirm it covers the Z18 build plate?

Each sheet measures 12.1 inches by 12.1 inches, matching the build surface of the MakerBot Replicator Z18.

How do I apply the tape to the Z18 plate without trapping air bubbles?

Clean the plate with isopropyl alcohol, then lay the tape from one edge and smooth it slowly with a plastic card to push air out.

When should I replace a sheet on the Z18?

Replace a sheet when prints no longer adhere cleanly or the surface shows tears, wrinkles or deep scratches.

Още от този рафт

Често сравнявани заедно

Същият рафт, същата каса — осем монети и заключване на курса за 30 минути.