Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Four square sheets of blue build-plate tape 12.1 inches each side

MakerBot

MakerBot MP06626 Build Plate Tape 4-Pack 12.1" x 12.1" Z18

SKU CH-WBNN-J5VYE MPN MP06626

Four sheets of 12.1-inch square build-plate tape sized for the MakerBot Replicator Z18

  • TypeBuild Plate Tape
  • SpecificationQuantity: 4-Pack Compatibility: MakerBot Replicator Z18 3D P
  • Four sheets ready for immediate bed changes
  • Each sheet measures 12.1" x 12.1" for full coverage
  • Designed specifically for the Replicator Z18 3D printer
  • Smooth surface promotes reliable first-layer adhesion
  • Packaged new as model MP06626 from MakerBot

Build Plate Tape for Z18

This four-pack of adhesive sheets is made for the MakerBot Replicator Z18 3D printer. Each sheet measures 12.1" x 12.1" to match the printer's build surface. The tape provides a textured layer that helps first-layer adhesion during printing. Users replace sheets when the surface wears or becomes damaged.

Replaces worn factory sheets

The tape substitutes the original build plate covering supplied with the Z18. A fresh sheet restores consistent adhesion without requiring bed levelling changes. The jump is worth it when prints start lifting at the corners or the existing tape shows deep gouges. Four sheets give multiple refreshes before reordering.

Suits Z18 owners needing quick swaps

Operators who run frequent jobs and want minimal downtime will value the pre-cut dimensions. Shops without a Z18 cannot use these sheets because the size is specific to that model. Buyers needing a different dimensions or a permanent build surface should look at other options.

Přednosti

  • Four sheets ready for immediate bed changes
  • Each sheet measures 12.1" x 12.1" for full coverage
  • Designed specifically for the Replicator Z18 3D printer
  • Smooth surface promotes reliable first-layer adhesion
  • Packaged new as model MP06626 from MakerBot

Specifikace

BrandMakerbot
ModelMP06626
TypeBuild Plate Tape
SpecificationQuantity: 4-Pack
Compatibility: MakerBot Replicator Z18 3D Printer
Dimension: 12.1" x 12.1 (W x L)
Přepravní hmotnost0.23 kg
Rozměry balení368 × 241 × 25 mm

Otázky k tomuto produktu

What are the exact dimensions of each tape sheet so I can confirm it covers the Z18 build plate?

Each sheet measures 12.1 inches by 12.1 inches, matching the build surface of the MakerBot Replicator Z18.

How do I apply the tape to the Z18 plate without trapping air bubbles?

Clean the plate with isopropyl alcohol, then lay the tape from one edge and smooth it slowly with a plastic card to push air out.

When should I replace a sheet on the Z18?

Replace a sheet when prints no longer adhere cleanly or the surface shows tears, wrinkles or deep scratches.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.