Acceptăm criptomonede — astfel, criptomonedele pe care le dețineți pot cumpăra echipamente reale.Plătiți în cripto, cheltuiți-o pe echipamente reale. Livrare asigurată gratuită oriunde în lume peste 399 $. Cartoane neutre, fără marcă, expediate din Germania.Livrare asigurată gratuită peste 399 $. Cursul dumneavoastră este blocat timp de 30 de minute de la deschiderea paginii de plată.Curs blocat 30 de minute. Fiecare articol este sigilat, numărul de serie este verificat, iar produsul este acoperit de o garanție de 24 de luni.Sigilat, garantat 24 de luni.

Produse urmărite Conectare
Four square sheets of blue build-plate tape 12.1 inches each side

MakerBot

MakerBot MP06626 Build Plate Tape 4-Pack 12.1" x 12.1" Z18

SKU CH-WBNN-J5VYE MPN MP06626

Four sheets of 12.1-inch square build-plate tape sized for the MakerBot Replicator Z18

  • TypeBuild Plate Tape
  • SpecificationQuantity: 4-Pack Compatibility: MakerBot Replicator Z18 3D P
  • Four sheets ready for immediate bed changes
  • Each sheet measures 12.1" x 12.1" for full coverage
  • Designed specifically for the Replicator Z18 3D printer
  • Smooth surface promotes reliable first-layer adhesion
  • Packaged new as model MP06626 from MakerBot

Build Plate Tape for Z18

This four-pack of adhesive sheets is made for the MakerBot Replicator Z18 3D printer. Each sheet measures 12.1" x 12.1" to match the printer's build surface. The tape provides a textured layer that helps first-layer adhesion during printing. Users replace sheets when the surface wears or becomes damaged.

Replaces worn factory sheets

The tape substitutes the original build plate covering supplied with the Z18. A fresh sheet restores consistent adhesion without requiring bed levelling changes. The jump is worth it when prints start lifting at the corners or the existing tape shows deep gouges. Four sheets give multiple refreshes before reordering.

Suits Z18 owners needing quick swaps

Operators who run frequent jobs and want minimal downtime will value the pre-cut dimensions. Shops without a Z18 cannot use these sheets because the size is specific to that model. Buyers needing a different dimensions or a permanent build surface should look at other options.

Puncte forte

  • Four sheets ready for immediate bed changes
  • Each sheet measures 12.1" x 12.1" for full coverage
  • Designed specifically for the Replicator Z18 3D printer
  • Smooth surface promotes reliable first-layer adhesion
  • Packaged new as model MP06626 from MakerBot

Specificații

BrandMakerbot
ModelMP06626
TypeBuild Plate Tape
SpecificationQuantity: 4-Pack
Compatibility: MakerBot Replicator Z18 3D Printer
Dimension: 12.1" x 12.1 (W x L)
Greutate la expediere0.23 kg
Dimensiunile coletului368 × 241 × 25 mm

Întrebări despre acest articol

What are the exact dimensions of each tape sheet so I can confirm it covers the Z18 build plate?

Each sheet measures 12.1 inches by 12.1 inches, matching the build surface of the MakerBot Replicator Z18.

How do I apply the tape to the Z18 plate without trapping air bubbles?

Clean the plate with isopropyl alcohol, then lay the tape from one edge and smooth it slowly with a plastic card to push air out.

When should I replace a sheet on the Z18?

Replace a sheet when prints no longer adhere cleanly or the surface shows tears, wrinkles or deep scratches.

Tot din acest raion

Clienții au comparat și acestea.

Același raion, aceeași finalizare a comenzii — opt monede și un curs blocat 30 de minute.