Vi tager imod kryptovaluta — så den krypto, du ejer, kan købe rigtig hardware.Betal med krypto, brug det på rigtig hardware. Gratis, forsikret levering til hele verden ved køb over 399 $. Neutrale, umærkede papkasser, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Din kurs låses i 30 minutter, så snart kassen åbner.Kurs låst i 30 minutter. Hver vare er forseglet, har kontrolleret serienummer og er dækket af 24 måneders garanti.Forseglet, 24 måneders garanti.

Prisvagt Log ind
Yellow PLA filament on 8.00 inch spool, 1.75mm diameter

BFKK

BFKK PLA Filament 1.75mm Yellow 1kg Spool 3D Printers Accessory

SKU CH-N88E-CVEGT

1.75 mm yellow PLA filament on a 1 kg spool with ±0.02 mm accuracy for most FDM printers

  • ColorYellow

Color Yellow

  • Reliable prints with no clogs, bubbles or tangles
  • 100% neat winding prevents snags and jams
  • ±0.02 mm accuracy fits almost every 1.75 mm FDM printer
  • 00" spool with 2.20" hub mounts on most machines
  • Print at 200–230 °C nozzle, 50–65 °C bed, 50–100 mm/s speed

PLA Filament 1.75 mm Yellow 1 kg

This PLA filament suits hobbyists and makers who print with FDM machines and want a bright yellow finish. It comes on a 1 kg spool sized at 8.00" diameter, 2.50" width and a 2.20" hub hole, so it fits most printer holders. The material is formulated for reliable extrusion and consistent layer adhesion.

Neat winding and tight tolerance

A self-developed winding device delivers a 100% neat rate that reduces tangles and jams during long prints. Dimensional accuracy is held to +/- 0.02 mm, keeping the 1.75 mm diameter within a narrow band that works across a wide range of FDM printers. These two factors together lower the chance of nozzle clogs and failed prints.

Simple setup with recommended settings

Load the spool, feed the filament and set the nozzle temperature between 200 and 230 °C, the bed temperature between 50 and 65 °C and the print speed between 50 and 100 mm/s. Problems usually arise when the hot-end runs cooler than 200 °C or the bed is left unheated, causing poor first-layer adhesion and warping.

Fordele

  • Reliable prints with no clogs, bubbles or tangles
  • 100% neat winding prevents snags and jams
  • ±0.02 mm accuracy fits almost every 1.75 mm FDM printer
  • 00" spool with 2.20" hub mounts on most machines
  • Print at 200–230 °C nozzle, 50–65 °C bed, 50–100 mm/s speed

Specifikationer

ColorYellow

Andre versioner af denne model

5 flere i samme serie

Samme familie, men med anden hukommelse, køler eller clockfrekvens — sammenlign, før du bestemmer dig.

Spørgsmål om denne vare

How often will the 1.75 mm spool need replacing during heavy printing?

A 1 kg spool lasts many prints; replacement frequency depends on model volume and infill settings.

What is the first limit reached during long prints at 100 mm/s?

Dimensional accuracy of ±0.02 mm and the recommended 200–230 °C nozzle range set the practical boundaries.

Does the PLA give off strong fumes or heat when running all day?

PLA prints at 200–230 °C with a 50–65 °C bed, producing low odour and minimal warping during extended sessions.

Også på denne hylde

Kunderne har også sammenlignet disse

Samme hylde, samme kasse — otte mønter og 30 minutters kurslås.