暗号資産でのお支払いに対応—お手持ちのコインで、本物のハードウェアをご購入いただけます。暗号資産で支払い、本物のハードウェアに使う。 $399以上のご注文で、世界中どこでも送料無料（保険付き）。無地・ノーブランドの外箱で、ドイツから発送いたします。$399以上で送料無料（保険付き）。 注文手続きを開始すると、レートは30分間ロックされます。レートは30分間ロック。 すべての商品は未開封で、シリアル番号を確認した上で、24か月保証が付いています。未開封、24か月保証。

ウォッチリスト ログイン
Yellow PLA filament on 8.00 inch spool, 1.75mm diameter

BFKK

BFKK PLA Filament 1.75mm Yellow 1kg Spool 3D Printers Accessory

SKU CH-N88E-CVEGT

1.75 mm yellow PLA filament on a 1 kg spool with ±0.02 mm accuracy for most FDM printers

  • ColorYellow

Color Yellow

  • Reliable prints with no clogs, bubbles or tangles
  • 100% neat winding prevents snags and jams
  • ±0.02 mm accuracy fits almost every 1.75 mm FDM printer
  • 00" spool with 2.20" hub mounts on most machines
  • Print at 200–230 °C nozzle, 50–65 °C bed, 50–100 mm/s speed

PLA Filament 1.75 mm Yellow 1 kg

This PLA filament suits hobbyists and makers who print with FDM machines and want a bright yellow finish. It comes on a 1 kg spool sized at 8.00" diameter, 2.50" width and a 2.20" hub hole, so it fits most printer holders. The material is formulated for reliable extrusion and consistent layer adhesion.

Neat winding and tight tolerance

A self-developed winding device delivers a 100% neat rate that reduces tangles and jams during long prints. Dimensional accuracy is held to +/- 0.02 mm, keeping the 1.75 mm diameter within a narrow band that works across a wide range of FDM printers. These two factors together lower the chance of nozzle clogs and failed prints.

Simple setup with recommended settings

Load the spool, feed the filament and set the nozzle temperature between 200 and 230 °C, the bed temperature between 50 and 65 °C and the print speed between 50 and 100 mm/s. Problems usually arise when the hot-end runs cooler than 200 °C or the bed is left unheated, causing poor first-layer adhesion and warping.

特長

  • Reliable prints with no clogs, bubbles or tangles
  • 100% neat winding prevents snags and jams
  • ±0.02 mm accuracy fits almost every 1.75 mm FDM printer
  • 00" spool with 2.20" hub mounts on most machines
  • Print at 200–230 °C nozzle, 50–65 °C bed, 50–100 mm/s speed

仕様

ColorYellow

このモデルの他のバージョン

同シリーズにさらに 5点

同じファミリーで、メモリ・クーラー・クロックが異なります — 購入前に比較してください。

この商品に関する質問

How often will the 1.75 mm spool need replacing during heavy printing?

A 1 kg spool lasts many prints; replacement frequency depends on model volume and infill settings.

What is the first limit reached during long prints at 100 mm/s?

Dimensional accuracy of ±0.02 mm and the recommended 200–230 °C nozzle range set the practical boundaries.

Does the PLA give off strong fumes or heat when running all day?

PLA prints at 200–230 °C with a 50–65 °C bed, producing low odour and minimal warping during extended sessions.

同じ売り場の商品

よく比較されている商品

同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。