Vi tager imod kryptovaluta — så den krypto, du ejer, kan købe rigtig hardware.Betal med krypto, brug det på rigtig hardware. Gratis, forsikret levering til hele verden ved køb over 399 $. Neutrale, umærkede papkasser, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Din kurs låses i 30 minutter, så snart kassen åbner.Kurs låst i 30 minutter. Hver vare er forseglet, har kontrolleret serienummer og er dækket af 24 måneders garanti.Forseglet, 24 måneders garanti.

Prisvagt Log ind

NEMIX RAM

NEMIX RAM 8GB DDR4 2933MHz PC4-23400 1Rx8 CL21 288-PIN ECC UDIMM memory upgrade

SKU CH-BH61-B60BV

8GB DDR4 2933MHz ECC UDIMM adds error-correcting memory to Supermicro X12SAE and X12SCA-F motherboards

  • Capacity8GB
  • Type288-Pin DDR4 ECC UDIMM
  • SpeedDDR4 2933 (PC4 23400)
  • CAS LatencyCL21
  • Voltage1.20V
  • ECCYes
  • ECC protects data integrity by correcting single-bit errors on the fly
  • 8 GB DDR4-2933 PC4-23400 matches Supermicro X12SAE and X12SCA-F spec exactly
  • 1Rx8 unbuffered UDIMM installs directly without registered or SODIMM mismatch
  • CL21 timing at 1.2 V runs at rated speed without manual tuning
  • Major OEM Samsung Micron Hynix chips deliver consistent reliability

8GB DDR4 ECC UDIMM for Supermicro Boards

This 8GB DDR4 2933MHz ECC unbuffered UDIMM is built for Supermicro X12SAE and X12SCA-F motherboards. It delivers 8GB of error-correcting memory at 1.2V with CL21 latency. The 288-pin module matches the exact rank and timing the platform expects for full-speed operation.

Suited for ECC server upgrades.

This module suits administrators upgrading Supermicro X12SAE or X12SCA-F systems that require unbuffered ECC UDIMMs. Builders needing registered DIMMs, SODIMM form factors, or non-ECC memory for consumer platforms should look elsewhere. Systems not validated for 1Rx8 DDR4-2933 ECC UDIMMs will not support this part.

288-pin DDR4 ECC UDIMM form factor

The single decisive specification is the 288-pin DDR4 ECC UDIMM form factor. Only motherboards wired for unbuffered ECC UDIMMs at DDR4-2933 will recognise this module at its rated 2933MHz speed and 8GB capacity. Any other slot type — RDIMM, SODIMM or non-ECC — will reject it physically or electrically.

Fordele

  • ECC protects data integrity by correcting single-bit errors on the fly
  • 8 GB DDR4-2933 PC4-23400 matches Supermicro X12SAE and X12SCA-F spec exactly
  • 1Rx8 unbuffered UDIMM installs directly without registered or SODIMM mismatch
  • CL21 timing at 1.2 V runs at rated speed without manual tuning
  • Major OEM Samsung Micron Hynix chips deliver consistent reliability

Specifikationer

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR4 ECC Unbuffered UDIMM Memory
Part NumberME23400-818K1
Capacity8GB
Type288-Pin DDR4 ECC UDIMM
SpeedDDR4 2933 (PC4 23400)
CAS LatencyCL21
Voltage1.20V
ECCYes
Buffered/RegisteredUnbuffered
Rank1Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR4 ECC Unbuffered UDIMM Motherboard Compatible
Package Content8GB DDR4 2933MHz PC4-23400 1Rx8 1.2V 288-PIN ECC UDIMM KIT

Andre versioner af denne model

5 flere i samme serie

Samme familie, men med anden hukommelse, køler eller clockfrekvens — sammenlign, før du bestemmer dig.

Spørgsmål om denne vare

Does my Supermicro X12SAE motherboard need a free 288-pin DDR4 UDIMM slot for this 8GB ECC module?

Yes. The module is a 288-pin DDR4 ECC UDIMM that fits the standard unbuffered DIMM slots on the X12SAE or X12SCA-F.

Can I mix this 1Rx8 CL21 stick with existing 2Rx8 DDR4-2933 ECC UDIMMs on the same board?

The X12SAE and X12SCA-F support mixed-rank populations; install modules in the order the manual specifies and the system will run at the lowest common speed and latency.

How can I confirm the module is running at DDR4-2933 with ECC active after installation?

Enter the BIOS or use a tool such as dmidecode; it should report 2933 MT/s, CL21, 1.20 V and ECC enabled for the new DIMM.

Også på denne hylde

Kunderne har også sammenlignet disse

Samme hylde, samme kasse — otte mønter og 30 minutters kurslås.