Vi tager imod kryptovaluta — så den krypto, du ejer, kan købe rigtig hardware.Betal med krypto, brug det på rigtig hardware. Gratis, forsikret levering til hele verden ved køb over 399 $. Neutrale, umærkede papkasser, sendt fra Tyskland.Gratis, forsikret levering over 399 $. Din kurs låses i 30 minutter, så snart kassen åbner.Kurs låst i 30 minutter. Hver vare er forseglet, har kontrolleret serienummer og er dækket af 24 måneders garanti.Forseglet, 24 måneders garanti.

Prisvagt Log ind

OWC

OWC 16GB (2x8GB) DDR3L 1600 CL11 ECC RDIMM Dell PowerEdge M610 M710

SKU CH-0SCN-BRCY8

Adds 16 GB of DDR3L 1600 ECC registered memory to Dell PowerEdge M610, M610X, M710 and M710HD servers

  • Capacity16GB (2 x 8GB)
  • Type240-Pin DDR3L ECC RDIMM
  • SpeedDDR3L 1600 (PC3L 12800)
  • CAS LatencyCL11
  • Voltage1.35V
  • ECCYes

Capacity 16GB (2 x 8GB)

  • ECC registered design prevents data errors in critical workloads
  • 16 GB kit (2 × 8 GB) expands server memory capacity
  • DDR3L 1600 CL11 at 1.35 V matches Dell PowerEdge specifications
  • 240-pin RDIMM form factor fits M610, M610X, M710 and M710HD blades
  • Replaces Dell part numbers A7134886, A7545680, RKR5J and SNPRKR5JC/8G

System-specific ECC RDIMM kit

This 16 GB kit contains two 8 GB DDR3L registered DIMMs built for Dell PowerEdge M610, M610X, M710 and M710HD blade servers. It is designed for workstation and server platforms that require ECC registered memory and will not work in standard desktop computers or alongside unbuffered modules.

Low-voltage DDR3L operation

Running at 1.35 V and DDR3L 1600 (PC3L-12800) with CL11 latency, the modules draw less power than standard DDR3 while meeting JEDEC specifications. The registered buffer reduces electrical load on the memory controller, helping maintain signal integrity in dense blade chassis without adding a heat spreader.

240-pin blade-server upgrade

Each module uses the 240-pin RDIMM form factor required by the target PowerEdge blades, freeing DIMM slots for further expansion within the system's supported population rules. The kit replaces Dell part numbers A7134886, A7545680, RKR5J and SNPRKR5JC/8G, letting administrators extend the service life of existing M610 and M710 platforms.

Fordele

  • ECC registered design prevents data errors in critical workloads
  • 16 GB kit (2 × 8 GB) expands server memory capacity
  • DDR3L 1600 CL11 at 1.35 V matches Dell PowerEdge specifications
  • 240-pin RDIMM form factor fits M610, M610X, M710 and M710HD blades
  • Replaces Dell part numbers A7134886, A7545680, RKR5J and SNPRKR5JC/8G

Specifikationer

BrandOWC
Part Number1R6T31R4016P
Capacity16GB (2 x 8GB)
Type240-Pin DDR3L ECC RDIMM
SpeedDDR3L 1600 (PC3L 12800)
CAS LatencyCL11
Voltage1.35V
ECCYes
Buffered/RegisteredRegistered
Rank1Rx4
Heat SpreaderNo
Compatible SystemDell PowerEdge M610
Dell PowerEdge M610X
Dell PowerEdge M710
Dell PowerEdge M710HD

Andre versioner af denne model

5 flere i samme serie

Samme familie, men med anden hukommelse, køler eller clockfrekvens — sammenlign, før du bestemmer dig.

Spørgsmål om denne vare

How do I install the 240-pin DDR3L RDIMM modules in a Dell PowerEdge M610, and what step is often missed?

Power down the server, open the chassis, align each module’s notch with the DIMM slot key, press firmly until the ejector tabs click, then verify in BIOS that all 16 GB are detected at 1600 MHz with ECC active.

What maintenance or replacement will the 1.35 V ECC registered kit need over its service life?

No routine maintenance is required; if a module fails, OWC’s limited lifetime advanced-replacement program covers a direct swap, and firmware updates on the M610 or M710 may improve compatibility.

What limit appears first when the 1Rx4 RDIMMs run sustained workloads on a PowerEdge M710?

The memory controller’s maximum supported frequency of 1600 MHz and the fixed CL11 latency become the bottleneck before thermal throttling, since the modules have no heat spreaders.

Også på denne hylde

Kunderne har også sammenlignet disse

Samme hylde, samme kasse — otte mønter og 30 minutters kurslås.