Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green rectangular circuit board with black chips and gold edge connector

A-Tech

A-Tech Supermicro Certified 4GB DDR3 1600 CL11 1.5V Non-ECC DIMM 240-Pin Desktop RAM

SKU CH-GDZP-KPS03

A 4 GB DDR3 1600 MHz desktop module with CL11 timing and 1.5 V operation, certified for Supermicro systems

  • Capacity4GB
  • SpeedDDR3 1600 (PC3 12800)
  • Tested Frequency1600
  • CAS LatencyCL11
  • Voltage1.50V
  • ECCNo
  • Supermicro certified for verified compatibility
  • Hynix chips deliver reliable DDR3 1600 operation
  • CL11 latency at 1.50 V standard voltage
  • Single 4 GB module in 240-pin DIMM form
  • Rigorously tested for dependable desktop performance

Certified Supermicro DDR3 Module

This 4GB DDR3 1600 DIMM carries Supermicro certification and uses Hynix chips in a 2Rx8 layout. It is built for desktop systems that require unbuffered non-ECC memory at standard 1.5V operation.

PC3-12800 speed and CL11 timing

The module runs at 1600MHz with a CAS latency of 11 cycles. DDR3 platforms cap usable bandwidth at the PC3-12800 rating, so this kit cannot exceed that ceiling even if the motherboard supports higher data rates.

240-pin installation and common issues

The 240-pin keyed edge connector drops straight into a DDR3 slot and locks with the side latches. Most problems arise when the slot generation is mismatched or when the BIOS leaves the module at a lower default frequency instead of the rated 1600MHz.

Kohokohdat

  • Supermicro certified for verified compatibility
  • Hynix chips deliver reliable DDR3 1600 operation
  • CL11 latency at 1.50 V standard voltage
  • Single 4 GB module in 240-pin DIMM form
  • Rigorously tested for dependable desktop performance

Tekniset tiedot

BrandSuperMicro
SeriesSupermicro Certified
ModelMEM-DR340L-HL02-UN16
Capacity4GB
SpeedDDR3 1600 (PC3 12800)
Tested Frequency1600
CAS LatencyCL11
Voltage1.50V
ECCNo
Buffered/RegisteredUnbuffered
ChipsetMajor Brand Chipset
Heat SpreaderNo
FeaturesSupermicro Certified MEM-DR340L-HL02-UN16 (Hynix)
Recommend UseCompatible Supermicro Systems

Kysymyksiä tästä tuotteesta

Will this 4GB DDR3 module work in my Supermicro motherboard?

The module is certified as Supermicro MEM-DR340L-HL02-UN16, so it is validated for compatible Supermicro systems. Check your board's manual for supported DDR3 1600 speeds and maximum capacity per slot.

Does this stick require ECC or registered memory slots?

No. It is a non-ECC, unbuffered DIMM, so it fits standard desktop DDR3 slots that accept non-ECC memory.

What do the CL11 and 1.5V figures mean for installation?

CL11 is the CAS latency at 1600 MHz, and 1.5V is the standard DDR3 voltage. Both are within JEDEC spec, so no BIOS voltage changes are needed.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.