SanDisk
SanDisk Cruzer Blade 8 GB USB 2.0 USB flash drive Black SDCZ50-008G-B35
$391.99
0.00502487BTC
在庫あり
A-Tech
A-Tech Supermicro Certified 4GB DDR3 1600 CL11 1.5V Non-ECC DIMM 240-Pin Desktop RAM
A 4 GB DDR3 1600 MHz desktop module with CL11 timing and 1.5 V operation, certified for Supermicro systems
- Capacity4GB
- SpeedDDR3 1600 (PC3 12800)
- Tested Frequency1600
- CAS LatencyCL11
- Voltage1.50V
- ECCNo
- Supermicro certified for verified compatibility
- Hynix chips deliver reliable DDR3 1600 operation
- CL11 latency at 1.50 V standard voltage
- Single 4 GB module in 240-pin DIMM form
- Rigorously tested for dependable desktop performance
Certified Supermicro DDR3 Module
This 4GB DDR3 1600 DIMM carries Supermicro certification and uses Hynix chips in a 2Rx8 layout. It is built for desktop systems that require unbuffered non-ECC memory at standard 1.5V operation.
PC3-12800 speed and CL11 timing
The module runs at 1600MHz with a CAS latency of 11 cycles. DDR3 platforms cap usable bandwidth at the PC3-12800 rating, so this kit cannot exceed that ceiling even if the motherboard supports higher data rates.
240-pin installation and common issues
The 240-pin keyed edge connector drops straight into a DDR3 slot and locks with the side latches. Most problems arise when the slot generation is mismatched or when the BIOS leaves the module at a lower default frequency instead of the rated 1600MHz.
特長
- Supermicro certified for verified compatibility
- Hynix chips deliver reliable DDR3 1600 operation
- CL11 latency at 1.50 V standard voltage
- Single 4 GB module in 240-pin DIMM form
- Rigorously tested for dependable desktop performance
仕様
| Brand | SuperMicro |
|---|---|
| Series | Supermicro Certified |
| Model | MEM-DR340L-HL02-UN16 |
| Capacity | 4GB |
| Speed | DDR3 1600 (PC3 12800) |
| Tested Frequency | 1600 |
| CAS Latency | CL11 |
| Voltage | 1.50V |
| ECC | No |
| Buffered/Registered | Unbuffered |
| Chipset | Major Brand Chipset |
| Heat Spreader | No |
| Features | Supermicro Certified MEM-DR340L-HL02-UN16 (Hynix) |
| Recommend Use | Compatible Supermicro Systems |
この商品に関する質問
Will this 4GB DDR3 module work in my Supermicro motherboard?
The module is certified as Supermicro MEM-DR340L-HL02-UN16, so it is validated for compatible Supermicro systems. Check your board's manual for supported DDR3 1600 speeds and maximum capacity per slot.
Does this stick require ECC or registered memory slots?
No. It is a non-ECC, unbuffered DIMM, so it fits standard desktop DDR3 slots that accept non-ECC memory.
What do the CL11 and 1.5V figures mean for installation?
CL11 is the CAS latency at 1600 MHz, and 1.5V is the standard DDR3 voltage. Both are within JEDEC spec, so no BIOS voltage changes are needed.
同じ売り場の商品
よく比較されている商品
同じ売り場、同じレジ — 8種類のコインと30分間のレートロック。
