Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Four matte black G1/4 compression fittings for 14mm rigid tubing

Bitspower

Bitspower BP-MBEMLA14-4P G1/4" Multi-Link Fitting 14mm OD Matte Black 4-pack liquid cooler

SKU CH-P75T-6ER89 MPN BP-MBEMLA14-4P

Four G1/4" brass compression fittings for 14mm OD hard tubing in a matte-black value pack

  • TypeFittings
  • Multi-link design extends rigid-tube runs
  • G1/4" thread fits standard water-cooling components
  • Brass construction resists corrosion under coolant
  • 14 mm OD compression seals hard tubing securely
  • Four matte-black fittings included for matching loops

G1/4" Multi-Link Fitting for 14mm Hard Tubing

This four-pack of Bitspower G1/4" multi-link compression fittings is built for custom liquid-cooling loops that use 14mm outer-diameter rigid tubing. The fittings are machined from high-quality brass and finished in a matte black coating. They suit builders who want a secure, low-profile way to extend or route hard-tube runs between components.

Replaces standard single compression fittings

A multi-link design lets you join two 14mm hard tubes in a straight line or through a bulkhead without adding separate couplers and extra seal points. The upgrade is worth it when you need a cleaner tube run, fewer potential leak paths, or a rigid extension that keeps alignment tight across longer spans.

Simple compression installation with hard tube prep

Slide the compression nut and olive onto the cut tube, seat the tube fully against the internal stop, then tighten the nut by hand plus a light turn with a fitting wrench. What usually goes wrong: tube ends cut at an angle or left with burrs prevent a full seat, and over-tightening can mar the matte finish or deform the brass olive.

Kohokohdat

  • Multi-link design extends rigid-tube runs
  • G1/4" thread fits standard water-cooling components
  • Brass construction resists corrosion under coolant
  • 14 mm OD compression seals hard tubing securely
  • Four matte-black fittings included for matching loops

Tekniset tiedot

TypeFittings

Kysymyksiä tästä tuotteesta

What outer-diameter rigid tubing fits the Bitspower BP-MBEMLA14-4P multi-link fitting?

The compression fitting is designed for 14 mm OD hard tubing, matching the size stated in the product name.

How do I install the G1/4" multi-link fitting without leaks, and what step is often missed?

Slide the compression ring and locking collar onto the tube, push the tube fully into the brass body until it seats, then hand-tighten the collar; the step often missed is verifying the tube bottoms out before tightening.

What maintenance or replacement will these brass fittings need over time?

Inspect O-rings annually for hardening or flattening; replace any that show wear, and re-torque collars if a loop is drained and refilled.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.