Přijímáme kryptoměny — takže to, co držíte, můžete utratit za skutečný hardware.Plaťte kryptem, utrácejte ho za skutečný hardware. Pojištěná doprava zdarma po celém světě nad 399 $. Neutrální přepravní krabice bez loga, odesílané z Německa.Pojištěná doprava zdarma nad 399 $. Jakmile se otevře pokladna, je váš kurz zablokovaný na 30 minut.Kurz zablokovaný na 30 minut. Každý výrobek je zapečetěný, jeho sériové číslo je zkontrolované a vztahuje se na něj 24měsíční záruka.Zapečetěno, záruka 24 měsíců.

Sledované položky Přihlásit se
Four matte black G1/4 compression fittings for 14mm rigid tubing

Bitspower

Bitspower BP-MBEMLA14-4P G1/4" Multi-Link Fitting 14mm OD Matte Black 4-pack liquid cooler

SKU CH-P75T-6ER89 MPN BP-MBEMLA14-4P

Four G1/4" brass compression fittings for 14mm OD hard tubing in a matte-black value pack

  • TypeFittings
  • Multi-link design extends rigid-tube runs
  • G1/4" thread fits standard water-cooling components
  • Brass construction resists corrosion under coolant
  • 14 mm OD compression seals hard tubing securely
  • Four matte-black fittings included for matching loops

G1/4" Multi-Link Fitting for 14mm Hard Tubing

This four-pack of Bitspower G1/4" multi-link compression fittings is built for custom liquid-cooling loops that use 14mm outer-diameter rigid tubing. The fittings are machined from high-quality brass and finished in a matte black coating. They suit builders who want a secure, low-profile way to extend or route hard-tube runs between components.

Replaces standard single compression fittings

A multi-link design lets you join two 14mm hard tubes in a straight line or through a bulkhead without adding separate couplers and extra seal points. The upgrade is worth it when you need a cleaner tube run, fewer potential leak paths, or a rigid extension that keeps alignment tight across longer spans.

Simple compression installation with hard tube prep

Slide the compression nut and olive onto the cut tube, seat the tube fully against the internal stop, then tighten the nut by hand plus a light turn with a fitting wrench. What usually goes wrong: tube ends cut at an angle or left with burrs prevent a full seat, and over-tightening can mar the matte finish or deform the brass olive.

Přednosti

  • Multi-link design extends rigid-tube runs
  • G1/4" thread fits standard water-cooling components
  • Brass construction resists corrosion under coolant
  • 14 mm OD compression seals hard tubing securely
  • Four matte-black fittings included for matching loops

Specifikace

TypeFittings

Otázky k tomuto produktu

What outer-diameter rigid tubing fits the Bitspower BP-MBEMLA14-4P multi-link fitting?

The compression fitting is designed for 14 mm OD hard tubing, matching the size stated in the product name.

How do I install the G1/4" multi-link fitting without leaks, and what step is often missed?

Slide the compression ring and locking collar onto the tube, push the tube fully into the brass body until it seats, then hand-tighten the collar; the step often missed is verifying the tube bottoms out before tightening.

What maintenance or replacement will these brass fittings need over time?

Inspect O-rings annually for hardening or flattening; replace any that show wear, and re-torque collars if a loop is drained and refilled.

Také v této kategorii

Zákazníci také porovnávali

Stejná kategorie, stejná pokladna — osm měn a kurz zamčený na 30 minut.