Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
A light grey filament spool, 750g, 2.85mm diameter

E3D Online

E3D Online spoolWorks EDGE Filament 2.85mm 750g Light Grey06 3d printers accessory

SKU CH-VEFA-6DSZK

Recyclable PETG-based filament, 2.85 mm diameter and 750 g, prints without fumes, adheres with gluestick and pairs with Scaffold support material

  • ColorGray
  • TypeFilament
  • Recyclable PETG-based material reduces environmental impact
  • Easy printing without unpleasant fumes or odours
  • Strong tough naturally glossy finish for durable parts
  • Adheres to bed with just a little gluestick
  • Pairs with Scaffold support for clean breakaway

Filament for 3D printing

E3D Online spoolWorks EDGE is a PETG-based filament supplied on a 750 g spool with a 2.85 mm diameter. It is formulated for makers who want the toughness of ABS together with the easy handling of PLA. The material prints with no unpleasant fumes or odours and produces a naturally glossy finish. It suits functional parts, prototypes and everyday models that need strength and reliable layer adhesion.

Check printer compatibility first

Verify that your 3D printer accepts 2.85 mm filament before ordering. The spool weighs 750 g, so confirm that your spool holder can accommodate that mass and width. A heated bed is recommended and a light coating of gluestick helps the first layer stick reliably. The filament pairs with E3D Scaffold support material if you need clean breakaway supports for complex geometries.

Low warp and stable extrusion

Edge is engineered for super-low contraction, which greatly reduces warping during printing. Managed viscosity and melt strength allow accurate overhangs and tight bridges without excessive cooling. The material maintains consistent flow at standard PETG temperatures, so fan noise and power draw stay typical for your printer. Parts come out strong and stiff with almost isotropic layer bonding.

Kohokohdat

  • Recyclable PETG-based material reduces environmental impact
  • Easy printing without unpleasant fumes or odours
  • Strong tough naturally glossy finish for durable parts
  • Adheres to bed with just a little gluestick
  • Pairs with Scaffold support for clean breakaway

Tekniset tiedot

BrandE3D
ModelEdge
ColorGray
TypeFilament

Kysymyksiä tästä tuotteesta

Does the 750 g spool of 2.85 mm Edge filament include any tools or adhesives?

The package contains only the filament spool. A glue stick for bed adhesion and a compatible 2.85 mm printer are purchased separately.

What distinguishes the Light Grey06 750 g spool from other Edge variants?

Light Grey06 is the specific colour identifier; the 750 g weight and 2.85 mm diameter are the only capacity and size options listed for this listing.

How does the 2.85 mm diameter affect printing on a Bowden setup?

The 2.85 mm format feeds reliably through longer Bowden tubes and matches printers designed for that filament size.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.