Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black ABS bracket converts a 5.25 inch bay to 2.5 or 3.5 inch drive plus 12cm fan mount

EN-Labs

EN-Labs INBR52512CMFAN 5.25 to 2.5 or 3.5 hard drive adapter with 12cm fan mount

SKU CH-78QY-PHHSA

Converts a 5.25" bay to hold one 2.5" or 3.5" SATA or SAS drive plus a 12 cm cooling fan

  • FeaturesSupports computer cases with an available 5.25 inch drive ba
  • Mount 2.5 or 3.5 drives in a 5.25 bay
  • Add a 12cm fan directly under the drive for active cooling
  • ABS plastic body keeps weight low and resists heat
  • Eight screws included for fast tool-free fitting
  • Compact 145 x 120 x .31 inch tray fits tight builds

Drive-bay adapter with fan mount

This EN-Labs adapter fits a 5.25-inch drive bay and accepts either a 2.5-inch or 3.5-inch SATA or SAS drive. It also provides a mounting point for a 12-centimetre cooling fan directly beneath the installed drive. The bracket is moulded from black ABS plastic and ships with eight mounting screws for quick installation.

Single-drive constraint

The tray holds exactly one drive at a time; a 2.5-inch SSD and a 3.5-inch HDD cannot be fitted simultaneously. Builders who need to run both a 2.5-inch and a 3.5-inch device must use two separate adapters or a different bay solution.

Sustained-load cooling

Mounting a 12-centimetre fan underneath the drive creates direct airflow across the drive surface during prolonged read or write sessions. This active cooling helps maintain consistent operating temperatures when the drive is under continuous load rather than brief bursts.

Kohokohdat

  • Mount 2.5 or 3.5 drives in a 5.25 bay
  • Add a 12cm fan directly under the drive for active cooling
  • ABS plastic body keeps weight low and resists heat
  • Eight screws included for fast tool-free fitting
  • Compact 145 x 120 x .31 inch tray fits tight builds

Tekniset tiedot

BrandEN-Labs
ModelINBR52512CMFAN
FeaturesSupports computer cases with an available 5.25 inch drive bay to Mount 1x 2.5“ OR 3.5" Drive and extra 12CM fan for cooling Can not mount a 2.5" SSD and a 3.5" HDD at the same time! Allow to Mount 1x 3.5 - inch(or 2.5 inch or SSD)Drive and 1x 12cm fan at the same time! Compatible with any 2.5 or 3.5 inch IDE,SATA or SAS Hard Drive and Solid State Disk,Converts an available 5.25" HDD bay drive to accommodate 3.5" HDD or 2.5'' SSD (Solid State Drive) Made of ABS(Acrylonitrile Butadiene Styrene) plastic body; quick and easy installation Above Install hard disk , below install the fan. D

Kysymyksiä tästä tuotteesta

Does the adapter let me keep using a 3.5" SATA drive and a 12 cm fan together in the same 5.25" bay?

Yes, the bracket is designed to hold one 3.5" drive and one 12 cm fan simultaneously, with the drive above and the fan below.

Which drive interfaces does the bracket accept when converting a 5.25" bay?

It works with any 2.5" or 3.5" IDE, SATA or SAS hard drive or solid-state disk, converting the bay without changing the drive's native connection.

What are the exact outer dimensions of the bracket so I can check clearance in my case?

The bracket measures 145 x 120 x 8 mm, which is approximately 5.71 x 4.72 x 0.31 inches overall.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.