Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Flatbed duplicator with four open SATA slots for 2.5 and 3.5 inch drives

EZ Dupe, Inc.

EZ Dupe HD Cyclone 600 1-to-4 SATA Duplicator 600MB/s

SKU CH-WXPB-1XKD3

Copies up to four SATA 2.5″ or 3.5″ drives at 600 MB/s with four copy modes and eight DoD-compliant erase modes

  • TypeHard Drive Duplicator
  • Target1 to 4
  • Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
  • Data Transfer Rate600MB/s
  • Operating TypeStandalone
  • ConnectorSATA

Target 1 to 4

  • 1 to 4
  • 1 to 19

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

Speed 600MB/Sec

  • 300MB/Sec
  • 600MB/Sec

Yliviivatut versiot ovat olemassa, mutta niitä ei ole varastossa täällä.

  • Copies up to 4 SATA drives simultaneously at 600 MB/s
  • Four duplication modes including quick and full copy options
  • Eight erase modes including DoD 5220.22-M 3-pass and 7-pass standards
  • Standalone operation requires no host computer or software
  • Supports 2.5" and 3.5" SATA HDDs and SSDs without adapters

Duplicator for up to four SATA drives

The EZ Dupe HD Cyclone 600 copies one source SATA drive to four targets simultaneously at 600MB/s. It handles 2.5" and 3.5" hard disks or solid-state drives without adapters. Operation is standalone, so no host computer or software is required for duplication or sanitisation tasks.

Open flatbed slots with AC power

Drives slide directly into the open platform slots; no trays or caddies are needed for SATA I, II or III devices. The unit runs from 115-230 V AC at 50/60 Hz and includes an auto power-off cool-down mechanism to protect drives during extended sessions.

Four copy modes and eight erase modes

Copy options include Quick Copy, Full Copy, Partition Copy and Percentage Copy for flexible imaging. Erase modes cover Quick Erase, Full Erase, DoD 3-pass, DoD 7-pass to 5220.22-M standard, Secure Erase, Enhanced SSD Erase and HPA/DCO removal for thorough sanitisation.

Kohokohdat

  • Copies up to 4 SATA drives simultaneously at 600 MB/s
  • Four duplication modes including quick and full copy options
  • Eight erase modes including DoD 5220.22-M 3-pass and 7-pass standards
  • Standalone operation requires no host computer or software
  • Supports 2.5" and 3.5" SATA HDDs and SSDs without adapters

Tekniset tiedot

BrandEZ Dupe
ModelHD Cyclone 600
Part NumberDM-HS3-HDD04
TypeHard Drive Duplicator
Target1 to 4
Supported MediaSATA Hard Drive Disk / SATA Solid State Drives
Data Transfer Rate600MB/s
Operating TypeStandalone
ConnectorSATA
Load TypeSlot
Power SupplyAC: 115-230 V, 50/60 Hz

Kysymyksiä tästä tuotteesta

What SATA interface speed does the duplicator support and what is the practical copy rate?

The unit connects via SATA and copies at up to 600MB/s, which equals 36GB per minute for each of the four target slots.

What drive sizes and form factors fit the open platform without adapters?

Both 2.5" and 3.5" SATA hard drives and solid state drives insert directly into the flatbed slots.

How is the duplicator set up and what step is often missed?

Connect the AC supply between 115V and 230V at 50/60Hz, insert source and target drives into the open slots, select a copy or erase mode from the front panel, and start the job; the step users forget is confirming the correct mode before pressing start.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.