Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Black anodised aluminium GPU brace, 15 mm square, telescopic from 74 to 120 mm

JONSBO

JONSBO VC20 GPU Brace Black 74-120mm 36g

SKU CH-AX4E-7A56T

Adjustable aluminium GPU support brace extends 74-120 mm with magnetic silicone pads to prevent sag

  • OptionNormal
  • Adjustable 74–120 mm height fits most graphics cards
  • Magnetic ends with silicone pads prevent shock and scratches
  • Sandblasted AL6061 aluminium construction weighs only 36 g
  • Telescopic screw design keeps the GPU perfectly parallel
  • Compact 15 × 15 mm footprint suits tight builds

What the JONSBO VC20 is and who it is for

The JONSBO VC20 is a compact GPU brace designed to support heavy graphics cards and prevent PCB sag. It suits builders installing large video cards in standard cases where the rear bracket alone cannot keep the board level. The anodised aluminium body adds rigidity without occupying expansion slots. It is not for systems that rely on a back-plate or vertical mounting bracket for primary support.

Height range and mounting limits

The brace adjusts from 74 mm to 120 mm via a telescopic screw, covering most mid-tower clearances between the graphics card and the case floor or PSU shroud. Magnetic ends with silicone pads grip the card and the mounting surface without tools, but they require a flat ferrous area or a steel panel to hold securely. Cases with non-magnetic floors or unusually tall CPU coolers may leave the brace too short or too long.

Capacity and headroom

At 36 g the brace adds negligible weight while resisting the downward force of modern triple-slot cards. The 15 mm square cross-section fits between tightly spaced components and cable runs. It comfortably holds cards up to the length where the PCB meets the rear bracket; beyond that the lever arm exceeds the magnetic grip and the brace can detach.

Kohokohdat

  • Adjustable 74–120 mm height fits most graphics cards
  • Magnetic ends with silicone pads prevent shock and scratches
  • Sandblasted AL6061 aluminium construction weighs only 36 g
  • Telescopic screw design keeps the GPU perfectly parallel
  • Compact 15 × 15 mm footprint suits tight builds

Tekniset tiedot

BrandJONSBO
OptionNormal

Kysymyksiä tästä tuotteesta

Which JONSBO VC20 size fits my case clearance?

The brace extends from 74 mm to 120 mm via its telescopic screw, so measure the gap between your graphics card and the side panel or drive cage and pick a setting inside that range.

How much sag will the 36 g aluminium brace actually stop?

The sandblasted AL6061 column locks at the chosen height and the magnetic silicone pads grip both the card back-plate and the case floor, holding the PCB parallel under typical triple-slot cooler weight.

Does the VC20 mount with screws or just the magnetic feet?

It uses only the stronger magnets and silicone pads at both ends; no case screws or adhesive are required, so installation and removal take seconds.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.