Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Round development board with 1.28 inch circular LCD screen, Type-C connector and GPIO headers

LORDWORLD

LORDWORLD ESP32-S3 Development Board 1.28in Round LCD 2MB PSRAM 16MB Flash

SKU CH-71JE-B6QNV

A round 1.28 inch IPS display development board with an ESP32-S3 dual-core processor, 2MB PSRAM, 16MB flash, 2.4 GHz Wi-Fi, Bluetooth 5, a six-axis IMU and a lithium battery header

  • Round 1.28in IPS display shows colour graphics at 240×240
  • Dual-core Xtensa LX7 processor runs up to 240 MHz for responsive code
  • 2MB PSRAM plus 16MB Flash store larger projects and buffers
  • Onboard QMI8658 6-axis IMU detects motion and gesture input
  • 4 GHz Wi-Fi and Bluetooth 5 connect sensors and phones wirelessly

ESP32-S3 board with round LCD

The LORDWORLD ESP32-S3 Development Board integrates a 1.28inch round IPS display at 240×240 resolution with 65K color. An Xtensa 32-bit LX7 dual-core processor runs up to 240MHz with 512KB SRAM, 384KB ROM, 2MB PSRAM and 16MB Flash. It targets makers building wearable or compact IoT prototypes that need an on-board screen and motion sensing.

Type-C power and GPIO headers

A Type-C connector handles power and USB serial communication for programming. The board includes a 3.7V lithium battery recharge/discharge header for portable operation. GPIO headers expose configurable pins while an onboard QMI8658 6-axis IMU provides accelerometer and gyroscope data for gesture detection.

Check antenna needs and battery wiring

Verify that 2.4GHz Wi-Fi 802.11 b/g/n and Bluetooth 5 coverage suits the installation environment. Confirm the 3.7V battery header pinout matches your cell before connecting. Ensure your toolchain supports the Xtensa LX7 architecture and that the round 240×240 display format fits the intended enclosure.

Kohokohdat

  • Round 1.28in IPS display shows colour graphics at 240×240
  • Dual-core Xtensa LX7 processor runs up to 240 MHz for responsive code
  • 2MB PSRAM plus 16MB Flash store larger projects and buffers
  • Onboard QMI8658 6-axis IMU detects motion and gesture input
  • 4 GHz Wi-Fi and Bluetooth 5 connect sensors and phones wirelessly

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

What Wi-Fi standard does the board use and what band does it operate on?

The board uses 802.11 b/g/n Wi-Fi on the 2.4 GHz band with an onboard antenna.

What pin headers are provided for power and expansion?

A 3.7 V lithium battery recharge/discharge header and GPIO headers are onboard for power and I/O.

How is the board programmed and which port is used?

Connect the USB Type-C port to a computer; the integrated USB serial controller appears as a COM port for flashing firmware.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.