Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with black Ethernet jack and 40-pin header

LORDWORLD

LORDWORLD PoE HAT (H) for Raspberry Pi 5 / CM 5 development board

SKU CH-ZYRP-XE8YP

A Power-over-Ethernet HAT supplying 5 V 5 A to Raspberry Pi 5 or CM 5 via a single cable while fitting the official case and active cooler

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header for direct attachment to Raspberry Pi 5 or CM 5
  • Compatible with official Raspberry Pi 5 case for enclosed deployment
  • Works alongside official active cooler to maintain thermal performance

PoE HAT for Raspberry Pi 5 and CM 5

The LORDWORLD PoE HAT (H) is an expansion board that adds Power over Ethernet to a Raspberry Pi 5 or Compute Module 5. It draws power and data from a single Ethernet cable, removing the need for a separate USB-C power supply. The board is aimed at makers and engineers who want a tidy, cable-free deployment for headless or embedded projects.

Installation uses the standard 40-pin GPIO header

The HAT sits directly on the 40-pin GPIO header and is designed to fit inside the official Raspberry Pi 5 case. It also works alongside the official active cooler, so thermal performance is not compromised. The only common issue is ensuring the PoE switch or injector actually supports the 802.3af/at standard; non-standard passive injectors will not power the board.

Delivers 5 V at up to 5 A over 802.3af/at

The isolated switched-mode supply provides 5 V 5 A, which is enough for the Raspberry Pi 5 plus typical USB peripherals such as SSDs or cameras. Heavy loads like multiple high-current USB devices or power-hungry HATs stacked on top can exceed the 5 A limit, causing voltage droop or brown-outs. In those scenarios a separate high-current power supply becomes necessary.

Kohokohdat

  • Powers Raspberry Pi 5 via single Ethernet cable using IEEE 802.3 af/at standard
  • Delivers 5 V 5 A output through isolated switched-mode supply for stable operation
  • Fits standard 40-pin GPIO header for direct attachment to Raspberry Pi 5 or CM 5
  • Compatible with official Raspberry Pi 5 case for enclosed deployment
  • Works alongside official active cooler to maintain thermal performance

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

How can I verify the 5V 5A output is active after connecting the PoE HAT (H) to my Raspberry Pi 5?

The Raspberry Pi 5 should boot normally and show stable voltage readings in the OS when powered through the PoE HAT (H) using a compliant 802.3af/at injector or switch.

What comes with the PoE HAT (H) and do I need a separate PoE injector or switch?

The board includes the PoE HAT (H) with a standard 40PIN GPIO header; a separate IEEE 802.3af/at compliant PoE injector or switch and Ethernet cable are required to deliver power and data.

Is the PoE HAT (H) the right choice for both a Raspberry Pi 5 and a Compute Module 5 development board?

Yes, the PoE HAT (H) is designed for the Raspberry Pi 5 and CM 5 development board, fitting the 40PIN GPIO header and working with the official case and active cooler.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.