Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green rectangular HAT board with four USB-A ports, GPIO header, status LEDs, and a small slide switch

LORDWORLD

LORDWORLD Raspberry Pi USB HUB HAT 4 Port development board

SKU CH-0K1Q-H1KXX

A four-port USB 2.0 HAT with onboard USB-to-UART converter and status LEDs for Raspberry Pi boards

  • Four USB 2.0/1.1 ports expand connectivity for Raspberry Pi boards
  • Onboard USB-to-UART converter with enable switch simplifies serial debugging
  • Multi-status LEDs show power, UART and per-port activity at a glance
  • HAT form factor fits Pi 4B+, 4B, 3B+, 3B, 2B+ and Zero W/WH directly
  • New condition ensures reliable operation for development and IoT edge projects

Raspberry Pi USB HUB HAT

The LORDWORLD Raspberry Pi USB HUB HAT adds four USB ports to Raspberry Pi boards from the Zero W through the 4B+. It is aimed at makers and developers who need extra peripheral connections without occupying the single onboard USB port. The HAT format keeps the expansion mechanically secure and electrically aligned with the GPIO header.

Onboard UART with enable switch

An integrated USB-to-UART converter provides a dedicated serial console for debugging, and a hardware switch disables it when not needed to prevent signal conflicts. Status LEDs show power, UART activity and the state of each USB port so you can verify connections at a glance. The board draws power from the Pi and requires no separate supply.

USB 2.0 and 1.1 operation

All four downstream ports operate at USB 2.0 or 1.1 speeds, so attached devices run within the Pi’s native USB bandwidth. The HAT adds no active cooling and introduces negligible extra heat or noise in normal use. Power consumption stays within the limits of the host Pi’s own supply.

Kohokohdat

  • Four USB 2.0/1.1 ports expand connectivity for Raspberry Pi boards
  • Onboard USB-to-UART converter with enable switch simplifies serial debugging
  • Multi-status LEDs show power, UART and per-port activity at a glance
  • HAT form factor fits Pi 4B+, 4B, 3B+, 3B, 2B+ and Zero W/WH directly
  • New condition ensures reliable operation for development and IoT edge projects

Tekniset tiedot

BrandLORDWORLD

Kysymyksiä tästä tuotteesta

What USB standard does the four-port hub support and what speed does that limit each port to?

The hub is compatible with USB 2.0 and USB 1.1, so every port tops out at the 2.0 signalling rate.

What does the HAT need on the Raspberry Pi to physically mount and work?

It mounts on the standard 40-pin GPIO header found on Pi 4B, 3B+, 3B, 2B+ and Zero W or WH models.

How is the board installed and which step is often missed?

Press the HAT onto the GPIO header, then use the onboard switch to enable the USB-to-UART function before opening a serial terminal.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.