Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Grey aluminium two-bay M.2 SATA enclosure with USB-C port

MAIWO

MAIWO Dual-Bay M.2 SATA Enclosure Cloner 10Gbps USB3.2 Gen2x2 2230 2242 2260 2280

SKU CH-Y208-QWMXH

Dual-bay M.2 SATA enclosure and offline cloner with 10Gbps USB 3.2 Gen 2x2, fitting 2230 to 2280 drives

  • ColorGrey
  • MaterialAluminum / Steel
  • External InterfaceM.2 NVME 10GBPS
  • HDD Count SupportedM.2 NVMe SSD
  • Number of Bay2 Bay

Model NVME/SATA Clone

  • Dual-bay design holds two M.2 SATA SSDs up to 2280 length
  • Offline cloning copies data drive-to-drive without a host computer
  • USB 3.2 Gen 2×2 Type-C delivers up to 20 Gbps transfer speed
  • Aluminium and steel chassis dissipates heat for sustained performance
  • Tool-free trays let you swap drives in seconds

Dual-bay M.2 SATA cloner

This enclosure holds two M.2 SATA SSDs in lengths from 2230 to 2280 and lets you duplicate data between them without a computer. It is aimed at technicians and home users who need a standalone way to migrate or back up SATA-based M.2 drives. The aluminium-and-steel chassis acts as a heatsink during long copy sessions.

Offline clone button

Press the dedicated button to start a sector-by-sector copy from the source bay to the target bay; no host connection or software is required. The USB 3.2 Gen 2x2 Type-C link runs at up to 20 Gbps when the unit is attached to a PC for regular file access. Only SATA protocol drives are supported despite the M.2 form factor.

Tool-free trays

Each bay uses a sliding tray with a latch that secures 2230, 2242, 2260 and 2280 modules without screws. The most common mistake is inserting an NVMe drive, which fits physically but will not be recognised because the bridge only speaks SATA. Verify the drive label states SATA before closing the tray.

Kohokohdat

  • Dual-bay design holds two M.2 SATA SSDs up to 2280 length
  • Offline cloning copies data drive-to-drive without a host computer
  • USB 3.2 Gen 2×2 Type-C delivers up to 20 Gbps transfer speed
  • Aluminium and steel chassis dissipates heat for sustained performance
  • Tool-free trays let you swap drives in seconds

Tekniset tiedot

ColorGrey
MaterialAluminum / Steel
External InterfaceM.2 NVME 10GBPS
HDD Count SupportedM.2 NVMe SSD
Number of Bay2 Bay

Tämän mallin muut versiot

2 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

What does the 20 Gbps USB 3.2 Gen 2x2 rating mean for actual SSD speeds?

The 20 Gbps link is the theoretical maximum. Real-world throughput depends on the installed SSDs, the RAID mode chosen and the host controller, so sustained speeds will typically be lower.

How does the USB 3.2 Gen 2x2 Type-C interface limit performance?

It caps the enclosure at 20 Gbps. If your host port is only USB 3.2 Gen 2 (10 Gbps) or USB 3.2 Gen 1 (5 Gbps), the enclosure will negotiate down to that lower speed.

Which M.2 lengths fit in the two bays?

Both bays accept 2230, 2242, 2260 and 2280 form-factor SSDs. The aluminium and steel chassis uses tool-free sliders to secure each length.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.