Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Rectangular 4U mining PSU with black 14cm fan and multiple 12V connectors

myVolts

myVolts 1800W ATX Mining Power Supply 10×12V 14cm Fan

SKU CH-1HD5-BSGR6

An 1800 W ATX unit with ten 12 V connectors, active PFC, six protection circuits and a 14 cm quiet fan

  • TypeAT
  • Delivers 1800W for high-density mining rigs
  • Ten 12 V connectors power multiple graphics cards
  • Active PFC corrects input from 180 to 240 V
  • Six safety circuits guard against voltage and current faults
  • 14 cm fan cools quietly with insect-resistant grille

Mining power supply 1800W

This ATX power supply delivers 1800W for multi-GPU mining rigs. It operates on 180-240V input with active PFC and a dual 12V rail design based on the 12V 2.3 specification. The unit includes ten 6-pin connectors for graphics cards and a 6-pin CPU power interface.

Upgrade from lower-wattage ATX units

Replaces standard desktop power supplies when a build needs more than ten 12V outputs for mining cards. The jump is worth it when a single rail cannot feed all GPUs or when the existing unit lacks the 12V 2.3 dual-rail layout required by the motherboard and graphics interfaces.

Ten 12V outputs with six protections

Comfortably handles mining configurations that demand ten simultaneous 6-pin connections under continuous load. Over-voltage, under-voltage, over-current, overload, short-circuit and anti-thunder protections guard the system. Headroom runs out when the total draw exceeds 1800W or when additional connector types beyond 6-pin are required.

Kohokohdat

  • Delivers 1800W for high-density mining rigs
  • Ten 12 V connectors power multiple graphics cards
  • Active PFC corrects input from 180 to 240 V
  • Six safety circuits guard against voltage and current faults
  • 14 cm fan cools quietly with insect-resistant grille

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

What form factor does this 1800W unit use and will it fit a standard ATX case?

The supply follows the ATX 12V 2.0 standard and includes a 14cm fan, so it matches the depth and mounting holes of a regular ATX power supply.

Which cables must be connected first when installing this mining PSU to avoid a no-post situation?

Plug the 24-pin ATX motherboard cable and the 6-pin CPU power connector before attaching any of the ten 12V graphics-card leads; the board will not initialise without both primary feeds.

How often should the 14cm cooling fan be cleaned in a dusty mining environment?

Remove the side panel and blow compressed air through the fan grille every three to six months; the anti-insect grille reduces blockages but fine dust still builds up on the blades.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.