Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Rectangular metal-cased power supply 213 by 112 by 50 mm with built-in fan and voltage selector switch

myVolts

myVolts S-360-24 24V 15A 360W power supply

SKU CH-C7JE-V2AX1 MPN S-360-24

24V 15A regulated switch-mode supply delivering 360W with 85% efficiency, manual 110/220V input selection and short-circuit, overload and over-voltage protection in a metal case

  • TypeAT
  • Delivers 360 W at 24 V and 15 A for demanding 3D printers and automation gear
  • Operates on 100–260 V input with a manual 110 V/220 V selector switch before power-on
  • Built-in overload, over-voltage and short-circuit protection guards connected equipment
  • Metal case with temperature-controlled fan runs from 10 to 60 °C for quiet, reliable cooling
  • Compact 213×112×50 mm footprint weighs only 765 g for easy indoor installation

360W 24V Industrial Switching Supply

This 360W switching power supply delivers a regulated 24V output at 15A for 3D printers, LED displays, automation gear and computer projects. A metal case houses the full-bridge circuit with pulse-width modulation and a temperature-controlled fan. Manual 110V/220V selection covers 100–260V mains input. Efficiency reaches 85%.

Suits fixed indoor 24V DC loads up to 360W

Makers, integrators and technicians powering 3D printers, industrial sensors or LED strips from a bench or cabinet will find the voltage and protection set a match. Builders needing adjustable voltage, multiple rails, ATX connectors or outdoor-rated enclosures should look elsewhere. The unit is indoor-only and provides a single fixed rail.

24V 15A single-rail output decides fit

The supply delivers exactly 24V at up to 15A on one DC rail, so the project must accept that fixed voltage and current ceiling. Over-voltage, overload and short-circuit protection guard the load, but no other voltage or connector options exist. Confirm the 24V 15A requirement before ordering.

Kohokohdat

  • Delivers 360 W at 24 V and 15 A for demanding 3D printers and automation gear
  • Operates on 100–260 V input with a manual 110 V/220 V selector switch before power-on
  • Built-in overload, over-voltage and short-circuit protection guards connected equipment
  • Metal case with temperature-controlled fan runs from 10 to 60 °C for quiet, reliable cooling
  • Compact 213×112×50 mm footprint weighs only 765 g for easy indoor installation

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

How do I install the S-360-24 and which step is most often missed?

Mount the 213 by 112 by 50 mm metal case indoors, then set the manual 110/220 V selector to match your mains before applying power; skipping the voltage check risks immediate damage.

What maintenance or replacement will this unit need later?

The built-in fan runs automatically based on temperature; plan to clean dust from the vents periodically and replace the fan if it becomes noisy or stops spinning.

What limit appears first during sustained high-load use?

The 10 to 60 °C operating range caps continuous output; above 60 °C the protection circuits will shut the 360 W unit down until it cools.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.