Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Rectangular aluminium power supply, silver finish, screw terminals visible, 85 by 58 by 33 millimetres

myVolts

myVolts S-48-24 24V 2A 48W power supply

SKU CH-QBZ9-JAZQQ

Compact aluminium switch-mode unit delivers 24 V at 2 A (48 W) with overload, over-voltage and short-circuit protection for industrial, LED and 3D-printer use

  • TypeAT
  • High efficiency with low DC ripple for stable output
  • Built-in short-circuit, overload and overvoltage protection
  • 100 % full-load burn-in test confirms reliable operation
  • Compact aluminium-alloy chassis measuring 85 x 58 x 33 mm with natural cooling
  • Wide AC 100-240 V input suits global mains supplies

Industrial 24 V power supply

The myVolts S-48-24 is a 48 W switch-mode unit that delivers 24 V at 2 A from a 100-240 V AC input. Its aluminium alloy case measures 85 x 58 x 33 mm and relies on natural convection for cooling. The supply suits industrial automation, LED displays, CCTV, 3D printers and similar engineering tasks.

Replaces open-frame or enclosed linear units

Builders moving from larger linear supplies gain a smaller footprint and lower operating temperature. The jump is worthwhile when space is limited, when 0-40 °C ambient operation is required, or when CCC, FCC and CE marks are needed for compliance. The 100 % burn-in test adds confidence for continuous duty.

Limited to 48 W and fixed 24 V output

The ADJ terminal allows only minor voltage trimming, not a wide range. Overload, over-voltage and short-circuit protection shut the unit down rather than fold back current. Natural convection demands free airflow around the 33 mm height; sealed enclosures above 40 °C or loads above 2 A will exceed the design limits.

Kohokohdat

  • High efficiency with low DC ripple for stable output
  • Built-in short-circuit, overload and overvoltage protection
  • 100 % full-load burn-in test confirms reliable operation
  • Compact aluminium-alloy chassis measuring 85 x 58 x 33 mm with natural cooling
  • Wide AC 100-240 V input suits global mains supplies

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

What are the exact mounting dimensions for the 85 x 58 x 33 mm aluminum alloy case?

The supply measures 85 mm long, 58 mm wide and 33 mm high, with a natural-cooling aluminium chassis that fits standard DIN-rail or panel cut-outs matching those centres.

Which terminals do I wire for AC input and DC output, and what is the common polarity mistake?

Connect live and neutral to the L and N pins for 100-240 V AC; the V terminal is +24 V and GND is 0 V — reversing V and GND is the frequent error that triggers the short-circuit protection.

When should I plan to replace the electrolytic capacitors inside this 48 W unit?

At the rated 0-40 °C operating range the capacitors typically last several years; expect shorter life if the supply runs continuously near 40 °C or in 95 % humidity, so schedule a preventive swap after 3-5 years in harsh environments.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.