Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Rectangular aluminum power supply, silver finish, screw terminals visible

myVolts

myVolts S-600-24 24V 25A 600W Power Supply

SKU CH-93D0-JM2BE

A 24V 25A 600W aluminium switch-mode supply with overload, over-voltage and short-circuit protection, certified to CCC, FCC and CE, rated for 0–40 °C operation

  • TypeAT
  • High efficiency with low DC ripple for stable power
  • Low operating temperature extends service life
  • circuit, overload and overvoltage protection built in
  • 100 % full-load burn-in test ensures reliability
  • High insulation strength meets CCC, FCC and CE standards

24 V 25 A 600 W Industrial Power Supply

This myVolts unit delivers a regulated 24 V DC output at up to 25 A for 600 W total power. It accepts AC input from 110 V to 220 V with a ±15 % tolerance. The aluminium alloy chassis uses natural convection cooling and includes short-circuit, overload and overvoltage protection. It carries CCC, FCC and CE safety compliance marks.

Suits fixed 24 V DC loads.

Engineers building LED displays, CCTV systems, 3D printers or industrial automation rigs will find the steady 24 V rail and protection suite appropriate. The supply operates from 0 °C to 40 °C and stores down to −20 °C. Buyers who need adjustable output voltage, redundant hot-swap modules or battery-backed operation should look at other designs.

Fixed 24 V DC output at 600 W

The single deciding specification is the continuous 24 V, 25 A rating giving 600 W. If the load requires exactly that voltage and current envelope, this unit matches; if the project demands a different voltage, higher current or a different form factor, another supply is required.

Kohokohdat

  • High efficiency with low DC ripple for stable power
  • Low operating temperature extends service life
  • circuit, overload and overvoltage protection built in
  • 100 % full-load burn-in test ensures reliability
  • High insulation strength meets CCC, FCC and CE standards

Tekniset tiedot

TypeAT

Kysymyksiä tästä tuotteesta

How can I verify the S-600-24 is working correctly after wiring the L, N, GND and V terminals?

Measure the DC output at the V and GND terminals with a multimeter; it should read close to 24 V under load, the unit should run within the 0–40 °C working range, and no protection fault should trigger.

What comes in the box with the S-600-24 and what must I source separately?

The supply itself with its aluminum-alloy chassis and terminal block for L, N, GND, V and ADJ is included; an AC mains cord, mounting screws and any load-side wiring are not supplied.

Which model from the comparison table should I choose for a 24 V 25 A 600 W requirement?

Choose the S-600-24, which is specified for 24 V output, 25 A current and 600 W power; the other listed models provide only 48 W or 60 W.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.