Akceptujemy kryptowaluty — posiadane środki można więc wykorzystać na zakup prawdziwego sprzętu.Płatność kryptowalutą — realny sprzęt w zamian. Bezpłatna, ubezpieczona dostawa na całym świecie powyżej 399 $. Neutralne kartony, bez oznaczeń, wysyłane z Niemiec.Bezpłatna, ubezpieczona dostawa powyżej 399 $. Kurs zostaje zablokowany na 30 minut od otwarcia kasy.Kurs zablokowany na 30 minut. Każdy produkt jest fabrycznie zapieczętowany, jego numer seryjny jest sprawdzany, a całość objęta jest 24-miesięczną gwarancją.Zapieczętowane fabrycznie, 24 miesiące gwarancji.

Obserwowane produkty Zaloguj się
Rectangular aluminum power supply, silver finish, screw terminals visible

myVolts

myVolts S-600-24 24V 25A 600W Power Supply

SKU CH-93D0-JM2BE

A 24V 25A 600W aluminium switch-mode supply with overload, over-voltage and short-circuit protection, certified to CCC, FCC and CE, rated for 0–40 °C operation

  • TypeAT
  • High efficiency with low DC ripple for stable power
  • Low operating temperature extends service life
  • circuit, overload and overvoltage protection built in
  • 100 % full-load burn-in test ensures reliability
  • High insulation strength meets CCC, FCC and CE standards

24 V 25 A 600 W Industrial Power Supply

This myVolts unit delivers a regulated 24 V DC output at up to 25 A for 600 W total power. It accepts AC input from 110 V to 220 V with a ±15 % tolerance. The aluminium alloy chassis uses natural convection cooling and includes short-circuit, overload and overvoltage protection. It carries CCC, FCC and CE safety compliance marks.

Suits fixed 24 V DC loads.

Engineers building LED displays, CCTV systems, 3D printers or industrial automation rigs will find the steady 24 V rail and protection suite appropriate. The supply operates from 0 °C to 40 °C and stores down to −20 °C. Buyers who need adjustable output voltage, redundant hot-swap modules or battery-backed operation should look at other designs.

Fixed 24 V DC output at 600 W

The single deciding specification is the continuous 24 V, 25 A rating giving 600 W. If the load requires exactly that voltage and current envelope, this unit matches; if the project demands a different voltage, higher current or a different form factor, another supply is required.

Najważniejsze cechy

  • High efficiency with low DC ripple for stable power
  • Low operating temperature extends service life
  • circuit, overload and overvoltage protection built in
  • 100 % full-load burn-in test ensures reliability
  • High insulation strength meets CCC, FCC and CE standards

Specyfikacja

TypeAT

Pytania dotyczące tego produktu

How can I verify the S-600-24 is working correctly after wiring the L, N, GND and V terminals?

Measure the DC output at the V and GND terminals with a multimeter; it should read close to 24 V under load, the unit should run within the 0–40 °C working range, and no protection fault should trigger.

What comes in the box with the S-600-24 and what must I source separately?

The supply itself with its aluminum-alloy chassis and terminal block for L, N, GND, V and ADJ is included; an AC mains cord, mounting screws and any load-side wiring are not supplied.

Which model from the comparison table should I choose for a 24 V 25 A 600 W requirement?

Choose the S-600-24, which is specified for 24 V output, 25 A current and 600 W power; the other listed models provide only 48 W or 60 W.

Także w tym dziale

Klienci porównywali też te produkty

Ten sam dział, ta sama kasa — osiem kryptowalut i 30-minutowa blokada kursu.