Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with black memory chips and gold edge connectors

NEMIX RAM

NEMIX RAM 128GB DDR5 4800 CL40 2Rx4 1.1V ECC RDIMM Supermicro X14SDV-20C-SP3F memory upgrade

SKU CH-EMRV-T2XG2

128GB DDR5 4800 ECC RDIMM, CL40, 1.1V, 2Rx4, 288-pin, validated for Supermicro X14SDV-20C-SP3F

  • Capacity128GB
  • Type288-Pin DDR5 RDIMM
  • SpeedDDR5 4800 (PC5 38400)
  • CAS LatencyCL40
  • Voltage1.10V
  • ECCYes

Size 128GB

  • 128 GB capacity lets the X14SDV-20C-SP3F reach its maximum supported memory
  • DDR5 4800 speed matches the board's rated frequency for full-performance operation
  • CL40 latency and 1.1 V voltage meet the exact timing and power spec the controller expects
  • Registered ECC 2Rx4 design offloads the memory controller and corrects single-bit errors on the fly
  • 288-pin RDIMM form factor is the precise module type required by this Supermicro motherboard

Supermicro X14SDV-20C-SP3F memory upgrade

This 128GB DDR5 RDIMM kit is built for the Supermicro X14SDV-20C-SP3F motherboard. It delivers registered ECC memory with a 2Rx4 organisation at 1.10V. The module matches the board's required 288-pin registered form factor and CL40 timing. Buyers needing unbuffered UDIMM or SODIMM modules cannot use this product.

Sustained load behaviour

Registered architecture buffers the command and address bus so every slot runs fully populated at the rated 4800 speed. ECC corrects single-bit errors on the fly, preventing silent data corruption during long compute runs. The 1.1V operation keeps power draw predictable under continuous server workloads. Builders who need higher frequencies or lower latencies than CL40 must look elsewhere.

Installation notes

The 288-pin RDIMM seats only in DDR5 RDIMM slots keyed for registered modules. Consult the Supermicro manual for the approved population order before fitting the kit. Mixing ranks or voltages will prevent the system from posting at full capacity. No heat spreader is fitted, so airflow across the module must be maintained by the chassis design.

Kohokohdat

  • 128 GB capacity lets the X14SDV-20C-SP3F reach its maximum supported memory
  • DDR5 4800 speed matches the board's rated frequency for full-performance operation
  • CL40 latency and 1.1 V voltage meet the exact timing and power spec the controller expects
  • Registered ECC 2Rx4 design offloads the memory controller and corrects single-bit errors on the fly
  • 288-pin RDIMM form factor is the precise module type required by this Supermicro motherboard

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Server Memory
ModelDDR5 ECC RDIMM Registered Server Memory
Part NumberMR38400-724K1
Capacity128GB
Type288-Pin DDR5 RDIMM
SpeedDDR5 4800 (PC5 38400)
CAS LatencyCL40
Voltage1.10V
ECCYes
Buffered/RegisteredRegistered
Rank2Rx4
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR5 ECC RDIMM Motherboard Compatible
Package Content128GB DDR5 4800MHz PC5-38400 2Rx4 1.1V 288-PIN ECC RDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

How much power does the 128GB DDR5 4800 CL40 2Rx4 1.1V ECC RDIMM draw when the server runs continuously?

The module operates at 1.10V, the standard DDR5 voltage for registered ECC DIMMs. Registered buffering reduces electrical load on the memory controller, so a fully populated Supermicro X14SDV-20C-SP3F stays within its normal power envelope without extra cooling.

What motherboard slot and memory population rules must the X14SDV-20C-SP3F already have to accept this 288-pin RDIMM kit?

The board needs a 288-pin DDR5 RDIMM slot and must support 2Rx4 registered ECC modules at 4800 MT/s. Check the manual for approved DIMM population order and maximum capacity per channel before installing.

Will this 128GB DDR5 4800 CL40 RDIMM work alongside older DDR5 4800 modules already installed in the X14SDV-20C-SP3F?

Yes, provided the existing modules are also DDR5 4800 registered ECC with matching rank and voltage. Mixing different speeds or ranks forces the memory controller to run all slots at the lowest common settings.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.