Hyväksymme kryptoa — hallussasi olevat kolikot voivat näin ostaa oikeaa laitteistoa.Maksa kryptolla, käytä se oikeaan laitteistoon. Ilmainen vakuutettu toimitus maailmanlaajuisesti yli 399 $. Neutraalit, tuotemerkittömät ulkopakkaukset, lähetetään Saksasta.Ilmainen vakuutettu toimitus yli 399 $. Kurssisi lukitaan 30 minuutiksi heti, kun kassa avautuu.Kurssi lukittu 30 minuutiksi. Jokainen tuote on sinetöity, sen sarjanumero on tarkistettu, ja sillä on 24 kuukauden takuu.Sinetöity, 24 kuukauden takuu.

Seuratut tuotteet Kirjaudu sisään
Green circuit board with black memory chips, no heat spreader, 288 gold pins along bottom edge

NEMIX RAM

NEMIX RAM 32GB DDR4 2933MHz ECC UDIMM CL21 2Rx8 1.2V 288-Pin Supermicro X12SCZ-F/TLN4F memory upgrade

SKU CH-0969-9K3F6

32 GB DDR4 ECC UDIMM at 2933 MHz CL21 1.2 V for Supermicro X12SCZ-F and TLN4F boards

  • Capacity32GB
  • Type288-Pin DDR4 ECC UDIMM
  • SpeedDDR4 2933 (PC4 23400)
  • CAS LatencyCL21
  • Voltage1.20V
  • ECCYes

Size 32GB

  • 32 GB capacity handles large datasets and virtual machines
  • ECC protection detects and corrects single-bit errors automatically
  • DDR4 2933 MHz speed matches the motherboard-rated memory controller frequency
  • 2Rx8 unbuffered UDIMM form factor fits the Supermicro X12SCZ-F and TLN4F slots exactly
  • 2 V operation at CL21 latency meets the board's voltage and timing requirements

Exact-Match Upgrade for Supermicro X12SCZ-F

This 32 GB DDR4-2933 ECC UDIMM is built to the precise rank, voltage and timing that the Supermicro X12SCZ-F and X12SCZ-TLN4F memory controllers expect. The single 2Rx8 module installs as a direct replacement or capacity increase without configuration changes. It serves administrators and workstation users who need guaranteed compatibility and error-correcting memory for data-integrity workloads.

288-Pin Unbuffered UDIMM Form Factor

The module uses the standard 288-pin DDR4 UDIMM edge connector required by the target motherboards, not an RDIMM or SODIMM layout. No heat spreader is fitted, keeping the profile low for dense DIMM populations and simplifying installation in tight server chassis. Builders must follow the board manual for approved population order and maximum supported capacity per slot.

ECC Reliability at 1.20 V Standard Voltage

Error-correcting code detects and corrects single-bit errors on the fly, preventing silent data corruption and unplanned reboots during continuous operation. The module runs at the JEDEC-standard 1.20 V, so power draw and thermal output remain at baseline DDR4 levels without additional cooling requirements. CL21 latency at 2933 MHz delivers the rated throughput the platform specifies.

Kohokohdat

  • 32 GB capacity handles large datasets and virtual machines
  • ECC protection detects and corrects single-bit errors automatically
  • DDR4 2933 MHz speed matches the motherboard-rated memory controller frequency
  • 2Rx8 unbuffered UDIMM form factor fits the Supermicro X12SCZ-F and TLN4F slots exactly
  • 2 V operation at CL21 latency meets the board's voltage and timing requirements

Tekniset tiedot

BrandNEMIX RAM
SeriesNEMIX RAM Original Series Memory
ModelDDR4 ECC Unbuffered UDIMM Memory
Part NumberME23400-328K1
Capacity32GB
Type288-Pin DDR4 ECC UDIMM
SpeedDDR4 2933 (PC4 23400)
CAS LatencyCL21
Voltage1.20V
ECCYes
Buffered/RegisteredUnbuffered
Rank2Rx8
ChipsetMajor OEM Samsung, Micron, Hynix
Heat SpreaderNo
Compatible SystemSupermicro
FeaturesDDR4 ECC Unbuffered UDIMM Motherboard Compatible
Package Content32GB DDR4 2933MHz PC4-23400 2Rx8 1.2V 288-PIN ECC UDIMM KIT

Tämän mallin muut versiot

5 lisää samasta mallistosta

Sama tuoteperhe, eri muisti, jäähdytin tai kellotaajuus — vertaile ennen päätöstä.

Kysymyksiä tästä tuotteesta

What speed and bandwidth does the DDR4 2933 (PC4-23400) interface deliver on the Supermicro X12SCZ-F?

The module runs at 2933 MT/s with a PC4-23400 data rate, so the memory controller on the X12SCZ-F can address the full 32 GB at its rated throughput.

Which physical slot and form factor does this 288-pin UDIMM require on the X12SCZ-F or TLN4F?

It fits a standard 288-pin DDR4 UDIMM slot; the board must accept unbuffered ECC UDIMMs, not RDIMMs or SODIMMs.

What is the correct installation order for this 2Rx8 kit on the Supermicro motherboard?

Consult the motherboard manual for the approved DIMM population sequence; install the module in the designated slot, press until the retention clips click, then verify full capacity in BIOS.

Myös tällä osastolla

Asiakkaat vertailivat myös näitä

Sama osasto, sama kassa — kahdeksan kryptovaluuttaa ja 30 minuutin kurssilukko.